Baking Pans, Cookies, Pies, Cakes, Peeking

ge.com

Baking Pans

Pan Placement

Safety

Use the proper baking pan. The type of finish on the pan determines the amount of browning that will occur.

■Dark, rough or dull pans absorb heat resulting in a browner, crisper crust. Use this type for pies.

■Shiny, bright and smooth pans reflect heat, resulting in a lighter, more delicate browning. Cakes and cookies require this type of pan.

■Glass baking dishes also absorb heat. When baking in glass baking dishes, the temperature may need to be reduced by 25°F.

■If you are using dark non-stick pans, you may find that you need to reduce the oven temperature 25°F to prevent over-browning.

For even cooking and proper browning, there must be enough room for air circulation in the oven. Baking results will be better if baking pans are centered as much as possible rather than being placed to the front or to the back of the oven.

Pans should not touch each other or the walls of the oven. Allow 1- to 11⁄2-inch space between pans as well as from the back of the oven, the door and the sides. If you need to use two shelves, stagger the pans so one is not directly above the other.

Instructions

Operating Instructions

Cookies

When baking cookies, flat cookie sheets (without sides) produce better-looking cookies. Cookies baked in a jelly roll pan (short sides all around) may have darker edges and pale or light browning

may occur.

Do not use a cookie sheet so large that it touches the walls or the door of the oven. Never entirely cover a shelf with a large cookie sheet.

For best results during baking, use only one cookie sheet in the oven at a time.

Troubleshooting

Pies

For best results, bake pies in dark, rough or dull pans to produce a browner, crisper crust. Frozen pies in foil pans should be placed on an aluminum cookie sheet for baking since the shiny foil pan reflects heat away from the pie crust; the cookie sheet helps retain it.

Cakes

When baking cakes, warped or bent pans will cause uneven baking results and poorly shaped products. A cake baked in a pan larger than the recipe recommends will usually be crisper, thinner and drier than it should be. If baked in a pan smaller than recommended, it may be undercooked and batter may overflow. Check the recipe to make sure the pan size used is the one recommended.

Tips

Peeking

Set the timer for the estimated cooking	DO NOT open the door to check until the
time and do not open the door to look at	minimum time. Opening the oven door
your food. Most recipes provide minimum	frequently during cooking allows heat to
and maximum baking times such as “bake	escape and makes baking times longer.
30-40 minutes.”	Your baking results may also be affected.

Consumer Support

JGRP20 specifications

The GE JGRP20 is a prominent jet engine widely used in modern aviation, recognized for its efficiency, power, and advanced engineering. Developed by General Electric, this engine serves as a key component in various commercial and military aircraft, offering a blend of performance and reliability that meets the demands of today's dynamic air transport sector.

One of the primary features of the JGRP20 is its advanced turbofan design, which allows for improved fuel efficiency and lower emissions compared to older engine models. The engine incorporates cutting-edge materials such as advanced composites and titanium alloys, which contribute to its lightweight structure while ensuring durability and longevity. This makes the JGRP20 an environmentally friendly choice, aligning with global efforts to reduce the carbon footprint of aviation.

The engine boasts a high bypass ratio, which enhances its thrust capabilities while operating at lower noise levels. This is particularly advantageous for urban airports where noise regulations are stringent. The combination of high bypass ratio and advanced aerodynamics enables the JGRP20 to deliver superior performance during takeoff and cruising phases of flight.

Advanced technologies integrated into the GE JGRP20 include digital engine control systems, which optimize performance and efficiency throughout the flight. With real-time monitoring and data analysis, the engine can adapt to varying flight conditions, ensuring optimal fuel consumption and thrust. Furthermore, the engine's component health monitoring system provides invaluable insights into the operational status, allowing for predictive maintenance and minimizing downtime.

In terms of operational versatility, the JGRP20 can be tailored to suit a range of aircraft configurations, making it a flexible solution for airlines and military operators alike. Its capacity for various thrust settings allows it to power a wide array of aircraft from regional jets to larger commercial airliners.

In summary, the GE JGRP20 represents the pinnacle of jet engine design and technology. With its commitment to efficiency, reduced emissions, and noise reduction, alongside its robustness and adaptability, it stands as a trusted choice for aviation stakeholders seeking reliable and high-performing engines for their fleets. This engine not only exemplifies GE's engineering prowess but also highlights the industry's ongoing evolution towards more sustainable air travel practices.

GE JGRP20 owner manual Baking Pans, Cookies, Pies, Cakes, Peeking

Models: JGRP20