Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

Support Troubleshooting Tips Care and Cleaning Operating Instructions

Use this appliance only for its intended use as described in this manual.

Do not attempt to repair or replace any part of your cooktop unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

Before performing any service, disconnect the cooktop power supply at the household distribution panel by removing the fuse or switching off the circuit breaker.

Be sure your appliance is properly installed and grounded by a qualified technician in accordance with the provided installation instructions.

Have the installer show you the location of the circuit breaker or fuse. Mark it for easy reference.

Do not leave children alone—children should not be left alone or unattended in an area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance.

Teach children not to play with the controls or any other part of the cooktop.

Do not allow anyone to climb, stand or hang on the cooktop.

CAUTION: Items of interest to children should not be stored in cabinets above a cooktop—children climbing on the cooktop to reach items could be seriously injured.

Always keep combustible wall coverings, curtains or drapes a safe distance from your cooktop.

Always keep dish towels, dishcloths, pot holders and other linens a safe distance away from your cooktop.

Always keep wooden and plastic utensils and canned food a safe distance away from your cooktop. They may become hot and could cause burns.

Never wear loose-fitting or hanging garments while using the appliance. Flammable material could be ignited if brought in contact with hot surface units and may cause severe burns.

Use only dry pot holders—moist or damp pot holders on hot surfaces may result in burns from steam. Do not let pot holders touch hot surface units. Do not use a towel or other bulky cloth. Such cloths can catch fire on a hot surface unit.

Do not use water on grease fires. Never pick up a flaming pan. Turn the controls off. Smother a flaming pan on a surface unit by covering the pan completely with a well-fitting lid, cookie sheet or flat tray. Use a multi-purpose dry chemical or foam-type extinguisher.

Flaming grease outside a pan can be put out by covering with baking soda or,

if available, by using a multi-purpose dry chemical or foam-type fire extinguisher.

When preparing flaming foods under the hood, turn the fan on.

Consumer

 

 

COOK MEAT AND POULTRY THOROUGHLY…

 

 

Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F and poultry

 

 

to at least an INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against

2

foodborne illness.

Page 2
Image 2
GE JP969, JP939 owner manual Safety Precautions, Consumer

JP939, JP969 specifications

The GE JP969 and JP939 are advanced jet engine variants designed to power the next generation of regional and narrow-body aircraft. With a commitment to enhanced efficiency, reliability, and performance, these engines incorporate cutting-edge technologies that significantly improve the overall flying experience while meeting stringent environmental regulations.

One of the defining features of the JP969 and JP939 is their high bypass ratio, which not only optimizes fuel efficiency but also minimizes noise pollution. By maximizing the amount of air that flows around the engine core, these engines achieve a perfect balance between thrust and environmental sustainability. This characteristic is essential for modern aviation as airlines seek to reduce their carbon footprints while maintaining operational efficiency.

Incorporating advanced materials technology, both the JP969 and JP939 benefit from lightweight composite fan blades and advanced alloys that can withstand extreme temperatures. This not only enhances the engines' durability but also contributes to their ability to maintain performance at high altitudes and during diverse operating conditions.

The engine control systems of the JP969 and JP939 are equipped with sophisticated digital engine control technology, enabling real-time monitoring and adjustments to optimize performance. This system enhances the operational flexibility of the engines, allowing them to adapt to varying flight profiles without compromising on efficiency or reliability.

Another key characteristic of these engines is their maintenance-friendly design. With an emphasis on reducing downtime, the JP969 and JP939 allow for easier access to critical components, thereby streamlining maintenance procedures. This feature is crucial for airlines aiming to maximize fleet availability and reduce operational costs.

Moreover, both engines incorporate state-of-the-art aerodynamics, with intricately designed fan blades and internal airflow paths that reduce drag and enhance overall performance. The thoughtful engineering behind these designs not only improves thrust but also contributes to reduced fuel consumption, making the JP969 and JP939 highly appealing for modern operators.

In conclusion, the GE JP969 and JP939 embody an impressive blend of efficiency, reliability, and advanced technology. Their high bypass ratio, innovative materials, sophisticated control systems, maintenance-friendly design, and aerodynamically optimized structures make them ideal choices for airlines looking to enhance their fleet's performance while adhering to environmental and operational standards. As aviation continues to evolve, these engines represent a significant leap forward in the pursuit of sustainable and efficient air travel.