IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by individuals possessing adequate backgrounds of electrical, electronic, and mechanical experience. Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use.

WARNING

To avoid personal injury, disconnect power before servicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened.

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY.

A.DO NOT OPERATE OR ALLOW THE OVEN TO BE OPERATED WITH THE DOOR OPEN.

B.IF THE OVEN OPERATES WITH THE DOOR OPEN, INSTRUCT THE USER NOT TO OPERATE THE OVEN AND CONTACT THE MANUFACTURER IMMEDIATELY.

C.MAKE THE FOLLOWING SAFETY CHECKS ON ALL OVENS TO BE SERVICED BEFORE ACTIVATING THE MAGNETRON OR OTHER MICROWAVE SOURCE, AND MAKE REPAIRS AS NECESSARY:

1.INTERLOCK OPERATION.

2.PROPER DOOR CLOSING.

3.SEAL AND SEALING SURFACES (ARCING, WEAR AND OTHER DAMAGE).

4.DAMAGE TO OR LOOSENING OF HINGES AND LATCHES.

5.EVIDENCE OF DROPPING OR ABUSE.

D.BEFORE TURNING ON MICROWAVE POWER FOR ANY TEST OR INSPECTION WITHIN THE MICROWAVE GENERATING COMPARTMENTS, CHECK THE MAGNETRON, WAVE GUIDE OR TRANSMISSION LINE AND CAVITY FOR PROPER ALIGNMENT, INTEGRITY AND CONNECTIONS.

E.ANY DEFECTIVE OR MISADJUSTED COMPONENTS IN THE INTERLOCK MONITOR, DOOR SEAL AND MICROWAVE GENERATION AND TRANSMISSION SYSTEMS SHALL BE REPAIRED, REPLACED OR ADJUSTED BY PROCEDURE DESCRIBED IN THIS MANUAL BEFORE THE OVEN IS RELEASED TO THE OWNER.

F.A MICROWAVE LEAKAGE CHECK TO VERIFY COMPLIANCE WITH THE FEDERAL PERFORMANCE STANDARD SHOULD BE PERFORMED ON EACH OVEN PRIOR TO RELEASE TO THE OWNER.

GE Consumer & Industrial

Technical Service Guide

Copyright © 2009

All rights reserved. This service guide may not be reproduced in whole or in part in any form without written permission from the General Electric Company.

– 2 –

Page 1 Page 3
Page 2
Image 2
GE JVM1750 manual GE Consumer & Industrial
Page 1 Page 3

JVM1750 specifications

The GE LVM1750, EVM1750, HVM1750, and JVM1750 are advanced energy management solutions designed to optimize the performance and reliability of industrial and commercial electrical systems. These products by General Electric (GE) are integral to modern power distribution networks, providing unprecedented efficiency and control.

The GE LVM1750 is a versatile low voltage motor control center that emphasizes compact design and high performance. One of its main features is the ability to accommodate a wide variety of motor and control configurations, making it suitable for diverse applications. It incorporates state-of-the-art technology to ensure quick troubleshooting and reduces downtime through its integrated diagnostic tools.

On the other hand, the EVM1750 is engineered for enhanced energy efficiency. This variant utilizes GE’s proprietary EcoStruxure technology, which facilitates real-time monitoring and control of energy consumption. The EVM1750 features advanced algorithms that optimize energy usage while maintaining operational integrity. This optimizes electricity demands during peak times, which can significantly reduce operational costs.

The HVM1750 is noteworthy for its robust construction and ability to handle high-voltage applications. Its main characteristics include superior thermal performance and advanced safety features designed to mitigate risks in high-demand environments. The HVM1750 is ideal for large industrial operations requiring reliable and efficient power management solutions.

Last but not least, the JVM1750 is tailored for renewable energy integrations. It provides crucial capabilities for managing distributed energy resources (DERs) and optimizing energy flows from renewable sources. The JVM1750 is equipped with smart grid capabilities, allowing seamless integration with other energy management systems. Its adaptability makes it an essential component in today’s shift toward sustainable energy practices.

All four models share characteristics such as scalability, reliability, and ease of maintenance. They are designed with user-friendly interfaces that simplify the monitoring and control processes. Furthermore, their modular designs allow for flexible configurations tailored to specific operational needs.

In summary, the GE LVM1750, EVM1750, HVM1750, and JVM1750 are leading-edge solutions that cater to the evolving demands of modern power distribution, emphasizing energy efficiency, safety, and adaptability. Through these innovations, GE continues to play a pivotal role in advancing electrical management technologies across industries.
Top Page Image Contents