GE PDW9000 Spots and filming Extremely hard water, On glasses, Prevent new film buildup, Seated

ge.com

Problem	Possible Causes	What To Do
Spots and filming	Extremely hard water	•	Use Jet-Dry® or Cascade Crystal Clear® rinse agents to remove spots and
on glasses and	Low inlet water temperature		prevent new film buildup.
flatware		•	Make sure water temperature is at least 120°F.
	Overloading the dishwasher
		•	Load dishwasher as shown in the Loading Place Settings section.
	Improper loading
		•	Make sure detergent is fresh.
	Old or damp powder detergent
		•	If water is extremely hard, a softener may be required.
	Rinse agent dispenser empty
	Too little detergent
Cloudiness on	Combination of soft water and	•	This is called etching and is permanent. To prevent this from happening,
glassware	too much detergent		use less detergent if you have soft water. Wash glassware in the shortest
			cycle that will get them clean. Recalibrate the SmartDispenseTM system if
			you are using it. See pages 9 and 11.
	Water temperature entering	•	This could be etching. Lower the water heater temperature.
	the dishwasher exceeds 150°F
Suds in the tub	Correct detergent	•	Use only automatic dishwasher detergents to avoid sudsing.
	wasn’t used		Cascade® and Electrasol® Automatic Dishwashing Detergents
			have been approved for use in all GE dishwashers.
		•	To remove suds from the tub, open the dishwasher and let
			suds dissipate. Close and latch the dishwasher door. Pump out water
			by touching the START/RESET pad once; then 30 seconds later,
			touch the START/RESET pad again. Repeat if necessary.
	Rinse agent was spilled	•	Always wipe up rinse agent spills immediately.
Detergent left in	Dishes are blocking the	•	Reposition the dishes, so the water from the lower spray arm can
dispenser cups	detergent cup or		flush the detergent cup or outlet from the SmartDispenseTM system.
or on door	SmartDispenseTM outlet		See pages 13 and 14.
Black or gray	Aluminum utensils have	•	Remove marks with a mild, abrasive cleaner.
marks on dishes	rubbed against dishes
Dishes don’t dry	Low inlet water temperature	•	Make sure inlet water temperature is at least 120°F.
		•	Select HEATED DRY.
		•	Use PRE WASH or ADDED HEAT options.
		•	Select a higher cycle, such as ANTI-BACTERIAor COOKWARE.
	Rinse agent dispenser is empty	•	Check the rinse agent dispenser and fill as required.
Control panel responded	Door latch may not be properly	•	Make sure the door is firmly closed.
to inputs but dishwasher	seated
never filled with water	Water valve may be turned off	•	Make sure water valve (usually located under the sink) is turned on.
Stained tub interior	Some tomato-based foods can	•	Use of the RINSE ONLY cycle after adding the dish to the load
	cause reddish stains		can decrease the level of staining. GE recommends Cascade®
			Plastic Booster to help remove these types of stains.
	Tea or coffee stains	•	Remove the stain by hand, using a solution of 1/2 cup bleach
			and 3 cups warm water.
			WARNING
			Before cleaning interior, wait at least 20 minutes after a cycle for the
			heating elements to cool down. Failure to do so can result in burns.
	An overall yellow or brown film can •		A special filter in the water supply line is the only way to correct
	be caused by iron deposits in water this problem. Contact a water softener company.
	White film on inside surface—	•	GE recommends Jet-Dry ® or Cascade Crystal Clear® to help
	hard water minerals		prevent hard water mineral deposits from forming.
		•	Run dishwasher with citric acid to remove mineral deposits. Citric
			acid (Part number: WD35X151) can be ordered through GE Parts.
			See back cover for ordering information.

17

Safety Instructions

Operating Instructions

Troubleshooting Tips

Consumer Support