Supported Firmware Versions
IED | Versions |
Product | Supported |
239 | 2.3x to 2.7x | |
|
|
|
269+ | 6.0x | |
|
|
|
369 | 1.6x to 2.3x | |
|
|
|
469 | 2.5x to 5.0x | |
489 | 1.3x to 4.0x | |
735/737 | 1.5x | |
745 | 2.4x to 5.0x | |
750/760 | 3.6x to 7.0x | |
F650 | 1.6x to 2.20 | |
MMII | 4.0x to 5.1x | |
MMIII | 1.0x to 1.2x | |
MIF2 | 1.0 |
|
PQM | 3.3x to 3.6x | |
PQMII | 1.0x to 2.2x | |
RRTD | 1.4x, 1.5x | |
SPM | 2.0x, 2.1x | |
|
|
|
B30 | 2.6x to 5.0x |
|
C30 | 2.6x to 5.0x |
|
C60 | 2.6x to 5.0x |
|
D30 | 3.0x to 5.0x |
|
D60 | 2.6x to 5.0x |
|
F35 | 2.6x to 5.0x |
|
F60 | 2.6x to 5.0x |
|
G30 | 4.4x to 5.0x |
|
G60 | 2.6x to 5.0x |
|
L60 | 2.6x to 5.0x |
|
L90 | 2.6x to 5.0x |
|
M60 | 2.6x to 5.0x |
|
N60 | 3.4x to 5.0x |
|
T35 | 2.6x to 5.0x |
|
T60 | 2.6x to 5.0x |
|
|
|
|
IED Product | Versions |
| Supported |
Spectra | 5.1x |
MicroVersa Trip |
|
Enhanced | 4.1x |
MicroVersa Trip C |
|
Enhanced | 4.1x |
MicroVersa Trip D |
|
EPM1000 | 3.8x |
EPM2000 | 1.0 |
EPM4000 | 3.8x |
EPM5000P | 2.4x |
EPM5200P | 2.4x |
EPM5300P | 2.4x |
EPM5350P | 2.4x |
EPM6000 | 1.0 |
EPM9450Q | 2.1x |
EPM9650Q | 2.1x |
PLEPM | 1.0x |
MX150 | 5.4x, 6.0x |
MX250 | 5.4x, 6.0x |
SMR2 | 1.0 |
MPRO | 1.0 |
FIRETRACER | 1.0 |
UPSLP | 1.0 |
UPSSG | 1.0 |
VERSAMAX | 1.0 |
Note:
UR has been categorized into three different Device Types.
UR - supports 2.6x to 4.6x
UR480 - supports 4.8x
UR490 - supports 4.9x and 5.0x
Basic steps to configure a system
Below is quick run thru of the basic steps to configure a system:
1.Install all the required hardware. This included any GE devices such meters, relays, breakers, etc.
2.Install and verify all required communication hardware and wiring. All serial, Ethernet, fiber (if used), etc. should be ‘rung’ out to verify their correct installation.
3.Configure all device communication settings. Modbus address, baud rate, IP address, etc. need to entered and recorded.
4.Add devices to Enervista PMCS using the Device Setup procedure below.
5.View any
6.View any automatically
5
