Manuals / Brands / Kitchen Appliance / Range / GE / Kitchen Appliance / Range

GE JGBS24, RGB523 20°, 21⁄8″, RIGHT EDGE, 6LEVELTHE RANGE, 7INSTALLTHE ANTI-TIPDEVICE

1 44

Download 44 pages, 1.62 Mb

Installation Instructions

6LEVELTHE RANGE

AInstall the oven racks in the oven

and position the range where it will be installed.

		Raise	Lower
		range	Lower
	Lower		range
	Lower
Leg	range
Leg
leveler
	Raise
	range
	(on some models)	(on some models)

BCheck for levelness by placing a spirit level or a cup, partially filled with water, on one of the oven racks. If using a spirit level, take two readings—with the level placed diagonally first in one direction and then the other.

CRemove the broiler drawer. See the Care and cleaning of the range section. The front leveling legs can be adjusted from the bottom and the rear legs can be adjusted from the top or the bottom.

DUse an open-end or adjustable wrench to adjust the leveling legs until the range is level.

EAfter the range is level, slide the range away from the wall so that the Anti-Tip device can be installed.

7INSTALLTHE ANTI-TIP DEVICE

WARNING —

•Range must be secured with an approved Anti-Tip device.

•Unless properly installed, the range could be tipped by you or a child standing, sitting or leaning on an open door.

•After installing the Anti-Tip device, verify that it is in place by carefully attempting to tilt the range forward.

•This range has been designed to meet all recognized industry tip standards for all normal conditions.

•The use of this device does not preclude tipping of the range when not properly installed.

•If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB02K10254.

AMark the wall where the RIGHT EDGE of the range is to be located. Be sure to allow for the countertop overhang if you intend to install the range next to cabinets.

	Anti-Tip
Slotted head	device
Slotted head
screw	Wallplate
	Wallplate
Approx. 20°
21⁄8″	Marked edge
21⁄8″	of range

BLocate the outside edge of the device

21⁄8 ″ toward the center of the range from the marked edge of the range.

CUsing the device as a template, mark the position of the hole for the screw.

37

Contents

Safety Instructions . . . .2–7,24 Operating Instructions Care and Cleaning Installation Instructions Safety Instructions or death ■ Do not try to light any appliance ■ Do not touch any electrical switch; do not use any phone in your building ■ If you cannot reach your gas supplier, call the fire department Tips Troubleshooting Instructions Installation Cleaning and Care Safety Tips Troubleshooting Instructions Installation Cleaning and Care Instructions LITE OFF Instructions Operating Instructions Before Lighting a Gas Burner How to Select Flame Size Top-of-RangeCookware Stove Top Grills Wok This Way In Case of Power Failure To Set the Clock To Set the Kitchen Timer To Change or Cancel the Kitchen Timer Setting Display Clock While Kitchen Timer Is Operating Before You Begin… Oven Control Oven Vent Instructions Installation Cleaning Power Outage How to Set the Oven for Baking or Roasting Preheating and Pan Placement Aluminum Foil Oven Moisture How to Set the Oven for Broiling Broiling Guide Suggestions Broiling Guide To Adjust the Thermostat Standard Twin Burner Assemblies (on some models) Drip Pans Burner Grates Burner Caps and Heads Cooktop Surface Stainless Steel Surfaces (on some models) Lift-Up Cooktop Lift-OffOven Door Oven Bottom Broiler Pan and Grid Removable Broiler Drawer (on some models) Oven Racks Porcelain Oven Interior If you have questions, call INTHE COMMONWEALTH OF MASSACHUSETTS BEFOREYOU BEGIN Read these instructions completely and carefully and Canadian Gas Association according to CAN/CGA-1.1latest edition FORYOUR SAFETY TOOLSYOU WILL NEED PART INCLUDED MATERIALSYOU MAY NEED NEW MUST NEVER BE LESS THAN 24 INCHES EXCEPTION: MUST DIMENSIONS AND CLEARANCES The range may be placed with 0″ clearance (flush) at the back wall 18″ 30″ 13″ LOCATION MODEL AND SERIAL NUMBER LOCATION IMPORTANT Take the accessory pack out of the oven and/or drawer Check to be sure that no range parts have come loose during shipping 1PROVIDE ADEQUATE GAS SUPPLY 2CONNECT THE RANGE TO GAS WARNING — DO NOT USE A FLAME TO CHECK FOR GAS LEAKS GAS PIPE AND ELECTRICAL OUTLET LOCATIONS (for models with Sealed Burners) FLEXIBLE CONNECTOR HOOKUP (for models equipped with Sealed Burners) RIGID PIPE HOOKUP OPTIONS (for models equipped with Sealed Burners) Alternate Hookup FLEXIBLE CONNECTOR HOOKUP (for models equipped with Standard Twin Burners) RIGID PIPE HOOKUP (for models equipped with Standard Twin Burners) 3ELECTRICAL CONNECTIONS Electrical Requirements Extension Cord Cautions Grounding IMPORTANT—(Pleaseread carefully) 3ELECTRICAL CONNECTIONS (cont.) DO NOT USE Electric Disconnect 4SEALTHE OPENINGS 5LIGHTTHE PILOTS 5LIGHTTHE PILOTS (cont.) BAdjust the Surface Burner Pilots if Necessary CLight the Oven Pilot CLight the Oven Pilot (cont.) DCheck Ignition of Oven Burner 260°F Electric ignition models To Remove the Broiler Drawer: FCheck Ignition of Surface Burners Standing Pilot Models Electric Ignition Models Quality of Flames (A) 6LEVELTHE RANGE 7INSTALLTHE ANTI-TIPDEVICE RIGHT EDGE 20° 21⁄8″ 7INSTALLTHE ANTI-TIPDEVICE (cont.) WHEN ALL HOOKUPS ARE COMPLETED CONVERTTO NATURAL GAS (or convert back to LP gas from natural gas) Problem Possible Causes What To Do Plug on range is not completely or do not burn evenly Troubleshooting Tips Page Safety Instructions Page Looking For Something More