Manuals / GE / Household Appliance / Heat Pump

GE SS1800, SS1000, SS500 manual GE Infrastructure Water & Process Technologies

Models: SS500 SS1800 SS1000

1 42

Download 42 pages 5.46 Kb

Page 1

OSMONICS

OSMONICS

TONKAFLO PUMPS

SS SERIES

INSTALLATION, OPERATION, AND

MAINTENANCE MANUAL

For SS500, SS1000, and

SS1800 Series

Tonkaflo Centrifugal

Pumps with X, XB, and XC

Motor Adapters

Without Bearing Frames

GE Infrastructure

Water & Process Technologies

Image 1

GE SS1800, SS1000, SS500 manual GE Infrastructure Water & Process Technologies, Osmonics Tonkaflo Pumps Ss Series

Contents

INSTALLATION, OPERATION, AND MAINTENANCE MANUAL GE Infrastructure Water & Process TechnologiesOSMONICS TONKAFLO PUMPS SS SERIES For SS500, SS1000, and SS1800 SeriesPage TABLE OF CONTENTS INSTALLATION, OPERATION AND MAINTENANCE MANUALFOR SS500, SS1000 AND SS1800 SERIES TONKAFLO CENTRIFUGAL PUMPSGENERAL TROUBLESHOOTING FOR ALL PUMPS LIST OF TABLES LIST OF FIGURESPage 1.0INTRODUCTION 2900 rpm Table Capacities3500 rpm MaximumTable Maximum Developed Boost Pressure SS SeriesMaximum Developed Number of CentrifugalM o d e l S S 1 8 4 8 X B M o d e l S S3.0PUMP INSTALLATION 3.1Inspection Figure Inlet Piping 3.3.3Pump Piping Connections PRIMED BEFORE START-UP Figure Installation of Discharge ScreenWARNING NEVER RUN PUMP DRY 3.6Motor Wiring 3.6.1Single-PhaseMotors Figure Changing Motor Rotation “Rolling” the Leads to Balance Current Draw MOTOR RUNS HOT OR STOPS LOW FLOWMOTOR DOES NOT RUN LOW PRESSUREWARNING BE CAREFUL NOT TO DAMAGE THE SHAFT Removal of Mechanical Seal Holder from Figure Removal of Pump Liquid-Endfrom FigureMotor Adapter 3.Remove the rotary portion spring, washer, and face assembly of the seal assembly from the pump shaft by rotating and pulling the rotary portion until it slides off the pump shaft Figure 4.6, Removal of Mechanical Seal Holder from Motor Adapter FORCE THE SHAFT INTO THE IMPELLER BORE STEPS 1.Disconnect the motor electrical power 5.0TONKAFLO PUMP FIELD MAINTENANCE2.Remove the wiring to the motor 5.1Motor Bearing Lubrication9.Reinstall the pump and pump piping connections 7.Install the four 4 5/16-18NCbolts and tighten10.Reinstall the motor wiring 1.Disconnect the motor electrical powerSTEPS 5.5Motor Installation X Motor Adapter PumpsPage 6.0LIQUID END - TONKAFLO SERVICE POLICY 7.2In-WarrantyPump Failure STEPS 7.1Motor Warranty7.3Out-of-WarrantyPump Failure 8.1500X Motor Adapter Pumps 8.0DIMENSIONAL DRAWINGSFigure 500X Motor Adapter Pump Figure 500 XB Motor Adapter Pump 8.2500 XB Motor Adapter PumpsFigure 1000X and Motor Adapter Pump 8.31000X and 1800X Motor Adapter PumpsFigure 1800XB Motor Adapter Pump 8.41800XB Motor Adapter PumpsFigure 1800XC Motor Adapter Pump 8.51800XC Motor Adapter PumpsFigure X Motor Adapter Pump 9.0CUTAWAY DRAWINGS 9.1 X Motor Adapter PumpFigure XB and XC Motor Adapter Pump 9.2XB and XC Motor Adapter PumpDescription Description Part NumberPart Number DescriptionDescription SeriesGE Infrastructure Water & Process Technologies 11.0ORDERING PARTS5951 Clearwater Drive Minnetonka, MN 55343-8995USA12.0WARRANTY TONKAFLO PUMP WARRANTY Page North American Sales GE Infrastructure Water & Process Technologies