Manuals / GE / Kitchen Appliance / Range

GE XL44 manual When All Hookups Are Completed, Make Sure All Controls Are Left In The Off Position

Models: XL44

1 48

Download 48 pages 12.36 Kb

Page 41

WHEN ALL HOOKUPS ARE COMPLETED:

For cement or concrete construction, you

will need a 1/4″ x 11⁄2″ lag bolt and a 1/2″ O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware.

Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware.

Wallboard	Back of
	range

Anti-Tip device

Wood screw

Wallplate

5.Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward.

WHEN ALL HOOKUPS ARE COMPLETED:

MAKE SURE ALL CONTROLS ARE LEFT IN THE OFF POSITION.

MAKE SURE THE FLOW OF COMBUSTION AND VENTILATION AIR TO THE RANGE IS UNOBSTRUCTED.

CONVERTING TO LP GAS

(or converting back to natural gas from LP)

This range leaves the factory set for use with natural gas. If you want to convert to LP gas, the conversion must be performed by a qualified LP gas installer.

The conversion instructions and LP orifices can be found attached to the range next to the pressure regulator.

Keep these instructions and the orifices in case you want to convert back to natural gas.

41

Image 41

GE XL44 manual When All Hookups Are Completed, Make Sure All Controls Are Left In The Off Position, Converting To Lp Gas

Contents

Installation Safety InstructionsCare and Cleaning RangesXL44 GasHELP US HELP YOU… Save time and money. Before you request service…WHAT TO DO IF YOU SMELL GAS Read this manual carefullyImportant Safety Instructions IMPORTANT SAFETY INSTRUCTIONSRead all instructions before using this appliance IMPORTANT SAFETY NOTICEIMPORTANT SAFETY INSTRUCTIONS Surface CookingSAVE THESE INSTRUCTIONS Cleaning Your RangeBaking, Broiling and Roasting Important Safety InstructionsMASK FOR SHELVES FEATURES OF YOUR RANGEFeatures and appearance vary Oven Light On/Off Switch on some models Features of Your RangeClock and Timer on some models See pageSurface Burner Controls SURFACE COOKINGBefore Lighting a Burner To Light a Surface BurnerTop-of-Range Cookware How to Select Flame SizeSurface Cooking Do not use a wok on any other support ringTo Set the Timer CLOCK AND TIMERTo Change or Cancel the Timer Setting Display Clock While Timer Is Operatingand Timer USING YOUR OVENUsing Your Oven Before Using Your OvenShelf Positions Oven ShelvesOven Vents USING YOUR OVENBAKING How to Set Your Range for BakingBaking Using Your OvenPreheating Pan PlacementBaking Guides CookiesCakes PiesBaking Pans Don’t PeekThe Type of Margarine Will Affect Baking Performance ADJUST THE OVEN THERMOSTATTo Adjust the Thermostat DO IT YOURSELFRoasting ROASTINGUse of Aluminum Foil Dual Shelf CookingROASTING GUIDE Questions and AnswersFrozen Roasts Q. Why is my roast crumbling when I try toBroiling BROILINGQuestions and Answers Q. When broiling, is it necessary to always use a grid in the pan?The oven and broiler compartment doors must be closed during broiling BROILING GUIDECleaning CARE AND CLEANINGGuide Care and Standard Twin Burners on some modelsCARE AND CLEANING Sealed Burner Assemblies on some modelsFor proper ignition Grate Burner cap Drip pan on some models Burner head ElectrodeBurner Grates Care and CleaningCooktop Surface Oven BottomControl Panel and Knobs Oven Light Bulb on some modelsRemovable Broiler Drawer on some models Broiler Pan and GridOven Air Vents Care and CleaningRemovable Storage Drawer on some models Removable Kick Panel on some modelsCARE AND CLEANING Lift-Off Oven DoorTO CLEAN THE DOOR Do not immerse door in water Inside of door Cautions about using spray-on oven cleanersStainless Steel Surfaces on some models Special Care of Continuous-Cleaning Oven Interior on some modelsCare and Cleaning To Clean the Continuous-Cleaning OvenFOR YOUR SAFETY INSTALLATION INSTRUCTIONSIn the Commonwealth of Massachusetts BEFORE YOU BEGIN361⁄4″± 1⁄4″ DIMENSIONS AND CLEARANCES36 ″ 40 ″GENERAL IMPORTANT SAFETY INSTRUCTIONSLOCATION INSTALLATION INSTRUCTIONSKITCHEN CABINETS PROTECT YOUR FLOORTOOLS YOU WILL NEED PREPARATION1 PROVIDE ADEQUATE GAS SUPPLY INSTALLATION INSTRUCTIONS2 CONNECT THE RANGE TO GAS Gas Pipe and Electric Outlet LocationsConnector Flexible Connector Hookup for Models Equipped with Sealed BurnersAlternate Hookup Rigid Pipe Hookup Options for Models Equipped with Sealed Burners2 CONNECT THE RANGE TO GAS continued INSTALLATION INSTRUCTIONS3 ELECTRICAL CONNECTIONS on some models Grounding4 SEAL THE OPENINGS Electric DisconnectAdjust the Surface Burner Pilots if Necessary INSTALLATION INSTRUCTIONS5 LIGHT THE PILOTS Light the Surface Burner PilotsQuality of Flames 6 CHECK IGNITION OF SURFACE BURNERS7 CHECK IGNITION OF OVEN BURNER Standing Pilot ModelsAir adjustment shutter Loosen INSTALLATION INSTRUCTIONSLoosen Air adjustment shutter To remove the oven bottomTo remove the broiler drawer To remove the oven bottom1. Remove knurled screws holding down rear of oven bottom INSTALLATION INSTRUCTIONS 2 1⁄ 8 ″11 INSTALLING THE ANTI-TIP DEVICE 10 LEVELING THE RANGECONVERTING TO LP GAS WHEN ALL HOOKUPS ARE COMPLETEDMAKE SURE ALL CONTROLS ARE LEFT IN THE OFF POSITION Page Before You Call for Service QUESTIONS? BEFORE YOU CALL FOR SERVICE…PROBLEM POSSIBLE CAUSEPROBLEM BEFORE YOU CALL FOR SERVICE…POSSIBLE CAUSE Do It Yourself sectionWarranty Registration Department P.O. Box Louisville, KY GE Service Protection PlusUnlimited service calls All parts and labor costs included We’ll Cover Any Appliance. Anywhere. AnytimeFollow these three steps to protect your new appliance investment online at GEAppliances.comModel Number Serial NumberParts and Accessories Schedule ServiceConsumer Support GE Appliances Websiteunder warranty WARRANTYWHAT IS COVERED WHAT IS NOT COVERED