GE Monogram ZIR36NDGE dimensions ZIR36ND-GEMonogram 36 Built-In All-Refrigerator

Monogram.™

ZIR36ND–GE Monogram 36" Built-In All-Refrigerator

Product Dimensions (in inches)

10-3/4" Max.

10" Min.

24-3/4"

26-3/4"

73-1/2"

4"

35" Case

36" Overall

84-1/2" Max.

83-1/2" Min.

Design Information

Designed to be installed flush or semi-flush with surrounding cabinetry. Cutout dimensions, clearances and side panel sizes are determined by the many installation options available. Side panels must be used whenever the sides of the refrigerator will be exposed. Side panels are not required when installed into an enclosure or between pantry and oven cabinets. IMPORTANT - Side panels, 1/2" minimum thickness are required when using FRAMELESS CABINETS.

•Field installed custom panels, Lexan® or stainless steel panels are required. The door and grille panel sizes vary to accommodate the kit being used.

•The supplied toekick is vented and must remain unobstructed for proper air circulation.

Optional Panel Kits:

•ZWBR36: Black Lexan® Panel Kit

•ZWWR36: White Lexan® Panel Kit

•ZWSR36: Stainless Steel Panel Kit

Optional Custom Trim Kits:

• ZKHR1: For installation of a custom handle of your choice onto a 1/4" Panel.

• ZKTR36LH or ZKTR36RH: For installation of a 3/4" thick custom panel.

• ZKHTR1: For installation of a custom handle of your choice onto a 3/4" thick

panel. (This kit must be used in combination with ZKTR36LH or ZKTR36RH).

• ZKHRSS1: Tubular Stainless Steel handle for 1/4" thick panel.

• ZKHTRSS1: Tubular Stainless Steel handle for 3/4" thick panel.

• ZGC2: 1/4" grille panel frame side pieces for 83-1/2" and 84-1/2" installation

		*Finished Width
		7 1/2"		Electrical	Wall View
				Area
	7"
	5"
84 1/2" max		24 3/4" Total			74" From Floor
83 1/2" min		Depth			to Bottom
Finished					of Electrical
Opening
	5"		Water Supply 5"		3 1/2"

3 1/2"

*36" Min. for a flush installation into an enclosure.

*35-1/2" Min. for a semi-flush installation into an enclosure. Note: Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout width to calculate rough-in width.

heights. (Factory set for 84").

• ZWT1: White toekick (supplied toekick is black).

• ZFC1: Trim strip for side-by-side installation of

two products.

Additional Specifications

•A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.

•Water line can enter opening through the floor or back wall. The water line should be 1/4" O.D. copper tubing between the cold water line and water connection location, long enough to extend to the front of the refrigerator. Installation of an easily accessible shut off valve is recommended.

Clearances:

•If the refrigerator or freezer is installed in a corner:

A 4" clearance is required on the hinge side for a 90° door opening and access to fresh food drawers. A 10" clearance is required on the hinge side to remove pans.

For answers to your Monogram,®

GE Profile Performance Series,™

GE Profile™ or GE appliance questions, call

GE Answer Center® service, 800.626.2000.

Specification Created 8/00

Listed by

Underwriters

RLaboratories