Gemini CDX-602 manual FLY CUE & CUE Instructions, And/Or, Troubleshooting, Robo Start Instructions

3.Push TRACK SKIP (13) to select the track you wish to play.

4.Press PLAY/PAUSE (16) and the unit will instantly play.

FLY CUE & CUE INSTRUCTIONS

The FLY CUE function lets you set cues “on the fly” with the press of a button. Press FLY CUE when the disc reaches the musical location you wish to make your cue or start point. The cue point is now programmed. Press CUE to return to the cue point. Press PLAY/PAUSE and the unit instantly starts from this pre-programmed spot.

AND/OR

1.To pre-program a cue point (the spot on a CD at which you want play to start) select the proper track and push PLAY/PAUSE so the unit enters the PLAY mode (PLAY/PAUSE LED glows green).

When the CD reaches the approximate musical spot you wish to make your cue, push PLAY/PAUSE so the unit enters the PAUSE mode (PLAY/PAUSE LED blinks). Move the SEARCH JOG WHEEL forward or in reverse until the precise spot at which you want CD play to begin is located. Push PLAY/PAUSE.

The cue point is now programmed. Press CUE to return to this pre-programmed cue point at any time. Push PLAY/PAUSE and the unit will instantly play from the pre-selected spot.

2.To fine tune your pre-programmed cue point, push PLAY/PAUSE so the unit enters the PLAY mode. Push the CUE button and the CD will return to the cue point you programmed in step #1 and begin play from that point. If you decide this cue or starting point is okay, leave the unit alone until you are ready to play.

3.If, however, the selected spot is not exactly where you want it, push the CUE button while the CD is playing and the disc will return to the pre-programmed cue point.

Locate the exact spot on the CD at which you want play to start by turning the SEARCH JOG WHEEL. Push PLAY/PAUSE to pre- program this new cue point. Press the CUE button to pause play at the new cue point. Push PLAY/PAUSE at any time and the unit will play from the pre-selected spot.

TROUBLESHOOTING

•If a disk will not play, check to see that it was loaded correctly (label side up) and that the CD unit is on a flat, level, stable surface. Check disc for dirt, scratches, spills, etc.

•If the disc spins but there is no sound, check the cable connections. If they are okay, check your amplifier or receiver.

•If the CD skips, check it for dirt, oil or scratches. Do not assume that the CD player or laser is defective. Many CDs are recorded “out of spec” and skip on most or all CD players.

Before sending the unit to an authorized Gemini service technician, insert a disc that plays properly in another unit.

CDX-602

ROBO START INSTRUCTIONS

IN SINGLE-AUTO CUE MODE:

Use ROBO START (25) in SINGLE-AUTO CUE MODE (5) to alternate play between the CDX-602’s two CD players (one track from one side, then one from the other). In SINGLE-AUTO CUE MODE play starts immediately with no blank or “dead” space. ROBO START causes one side of the CD player to play when the other side is paused.

1.Engage SINGLE-AUTO CUE MODE with the SINGLE-AUTO CUE/ CONTINUOUS button.

2.Press the ROBO START (25) button to activate ROBO START. Play will alternate between the two CD players. At the end of a track, the playing side pauses and the other CD deck plays a track. At the end of this track, the playing side pauses and the first CD deck resumes play.

IN CONTINUOUS MODE OR DURING NORMAL PLAY:

If you use the ROBO START function without SINGLE-AUTO CUE MODE (in CONTINUOUS MODE or during normal play), CD deck play does not alternate automatically. PAUSE must be pressed on the playing deck for the second deck to play.

1.During normal play, set a cue point on the second CD deck.

2.Press the ROBO START button to activate ROBO START.

3.Press PLAY/PAUSE BUTTON on the playing side to start play from the cue point on the other CD deck.

NOTE: Pausing play in the middle of a track causes the other CD deck to play. When the new track ends, play resumes on the first CD player from the point at which it was paused.

SPECIFICATIONS CDX-601/CDX-602

GENERAL:
Type	Compact Disc Player
Disc Type	Standard Compact discs (12 cm & 8 cm)
Time Display	Track Elapsed, Track Remain, or Total remain
Variable Pitch	± 12% Slider with Resume Switch
Pitch Bend	± 16% Maximum
Instant Start	Within 0.03 seconds
Track Selection	1 to 99 Tracks
Installation	19" each
Dimensions	19” x 3.5” x 10”
Weight Per Unit	9.5 lbs.
AUDIO SECTION:
Quantization	1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate	8 Times
Sampling Frequency	44.1 kHz
Frequency Response	20 Hz to 20 kHz
Digital Output	IEC958
Total Harmonic Distortion	Less Than 0.05%
Signal to Noise Ratio	104 dB
Dynamic Range	98 dB
Channel Separation	90 dB (1 KHz)
Output Level	1.9 Volts R.M.S.
Power Supply	AC 115/230V, 60/50 Hz

Page 5