
INTRODUCTION:
Congratulations on your purchase of a
&manufactured by Gemini Sound Products. The new Gemini GX speaker range includes the very latest technology in lightweight ABS design. Trapezoidal design for a more precise and accurate sound these speakers will add increased sound definition on vocal frequencies. Available as either 12” or 15” passive or powered units and complete with handles for easy transportation make the new
FEATURES:
All GX Speakers Come With Stand Mounts to Turn Your Speakers Into Stage Monitors. We’ve Also Included a Speaker Bag, All GX Speakers Have the Following:
• Aluminum | • Stand Mounting Socket | • | Auxiliary Line Outputs | |
• Metal Corners/Full Metal Grill | • High Temp Voice Coil | • | Rigging Points | |
• Rubber Feet | • Stacking Grooves | • Easy Carry Handles | ||
|
|
|
| |
• 12” Two Way Loudspeaker | • Compression Driver with 1.5” Titanium Diaphragm | |||
• 1/4” & Speakon Inputs |
| • Frequency Response | ||
• 200 Wrms, 800 Watts Peak Power | • 1/4” & SpeakonTM Outputs | |||
|
|
|
| |
• 15” Two Way Loudspeaker | • Compression Driver with 1.75” Titanium Diaphragm | |||
• 1/4” & Speakon Inputs |
| • Frequency Response | ||
• 300 Wrms, 1000 Watts Peak Power | • 1/4” & SpeakonTM Outputs | |||
|
|
|
| |
• Powered 12” Two Way Loudspeaker |
| • Bass & Treble Controls | ||
• Compression Driver with 1.5” Titanium Diaphragm | • 1/4” & XLR Line Outputs | |||
• XLR & RCA Line Inputs |
|
| • Frequency Response | |
• |
| • Clip & Power LED | ||
• 200 Wrms, 800 Watts Peak Power |
|
|
| |
|
|
|
| |
• Powered 15” Two Way Loudspeaker |
| • Bass & Treble Controls | ||
• Compression Driver with 1.75” Titanium Diaphragm | • 1/4” & XLR Line Outputs | |||
• XLR & RCA Line Inputs |
|
| • Frequency Response | |
• |
| • Clip & Power LED | ||
• 300 Wrms, 1000 Watts Peak Power |
|
|
|
CAUTIONS:
1.All operating instructions should be read before using this equipment.
2.To reduce the risk of electrical shock, do not open the unit. There are, NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified Gemini Sound Products service technician.
In the USA: If you experience problems with this unit, please call 1 (732)
3.Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4.This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents.
5.When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit.
6.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
LINE VOLTAGE SELECTION:
The GEMINI
115 or 230 volts. Be sure to set the proper voltage:
1.Place the head of a screwdriver in the center of the VOLTAGE SELECTOR (24) switch found on the rear panel.
2.Slide the switch to 115 or 230 volts.
3.Do not force or twist the switch. Excessive force may cause damage. If the switch does not move smoothly, contact a qualified technician.
CONNECTIONS:
Make sure ALL your equipment is completely OFF and lower ALL VOLUME, LEVEL, & GAIN controls and before connecting the speaker.
1.For the
2.For the
NOTE: ONLY THE
3.You can also use the AUXILIARY LINE OUTPUT JACKS (7, 13, & 14) to
NOTE: PLEASE REFER TO THE CONNECTIONS GUIDE FOR DETAILED DESCRIPTIONS!
OPERATION:
The speakers can be used in PAIRS for a NORMAL setup, or in groups of FOUR when
GX-300/400:
1.First turn on your MIXER or other signal source.
2.Then turn on your AMPLIFIER and increase the VOLUME or GAIN control as recommended by the AMPLIFIERS owner manual.
3.Start playing from your TURNTABLE, CD PLAYER, MIC, etc. and adjust the volume controls from your mixer to a reasonable level.
GX-350/450:
1.First turn on your MIXER/MICROPHONES or other signal source, then turn on your SPEAKER, the POWER LED (22) will be lit. Start playing from your TURNTABLE, CD PLAYER, MIC, etc. and adjust the volume controls from your MIXER/MICROPHONES, to a reasonable level.
2.Use the MIC/LINE LEVEL (15, 16) controls to adjust MIC 1, MIC 2 (9, 10), or LINE IN (11, 12) levels. The MIC/LINE LEVEL (15, 16) controls can be used to adjust the level of the LINE OUT (13, 14) signals as well.
3.Use the SPEAKER LEVEL (17) control to adjust the overall level of the SPEAKER, and use the TREBLE (18) & BASS (19) controls to adjust the TREBLE & BASS levels. If your MIC 1/MIC 2 (9, 10), LINE LEVEL (11, 12), or SPEAKER LEVEL (17) is too loud or distorted the CLIP LED (23) will be lit, at this point adjust your volume to an appropriate level.
CHAIN-LINK:
Only 1 additional speaker can be added to each speaker in a CHAIN- LINK setup. Connect your speakers first then follow the setup steps, your AMPLIFIER will compensate for the extra speakers.
SET-UP:
Use the provided mounting hardware for a STAGE MONITORING setup. Slide the plastic legs into the holes on the side of the speaker. Refer to the
SPECIFICATIONS:
SEE PAGE 10 FOR SPECIFICATIONS.
SHOULD YOU EXPERIENCE ANY DIFFICULTIES OR PROBLEMS, PLEASE CALL: 1 (732)
(6)