English

19.DON’T OVERREACH. Maintain proper footing and balance at all times; loss of balance can cause you to fall into the working machine, possibly causing an injury.

20.NEVER STAND ON THE TOOL. An injury may occur if the machine is tipped or if you should unintentionally contact the cutting tool.

21.DO NOT FORCE THE TOOL. The tool will perform the job better and safer at the feed rate for which it was designed. Forcing the tool could possibly damage the machine and may result in personal injury.

22.FEED THE WORK-PIECE IN THE CORRECT DIRECTION AND SPEED. Feed the work-piece into a blade, cutter, or abrasive surface against the direction of the cutting tool’s direction of rotation only. Incorrectly feeding the work-piece in the same direction as the cutting tool rotates causes the work-piece to be thrown out at high speed.

23.NEVER LEAVE THE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Don’t leave the machine until it comes to a complete stop.

24.TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE POWER SOURCE before adjusting or changing set-ups, or when making repairs. An accidental start-up may occur causing personal injury.

25.NEVER USE THE TOOL IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes.

26.KEEP THE TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean the tool.

27.DO NOT USE THE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

28.USE ONLY CORRECT BLADES. Do not use blades with incorrectly sized arbor holes. Never use blade washers or blade bolts that are defective or incorrect.

29.BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS ARE SECURE. DOUBLE CHECK ALL SETUPS. Make sure the blade is tight and not making contact with the saw or work-piece before connecting to the power supply.

30.AVOID CUTTING NAILS. Inspect for and remove all nails from lumber before cutting.

31.NEVER TOUCH THE BLADE OR OTHER MOVING PARTS DURING USE.

32.NEVER START A TOOL WHEN ANY ROTATING COMPONENT IS IN CONTACT WITH THE WORK-PIECE.

33.MAKE SURE THE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work.

34.INSPECT TOOL CORDS PERIODICALLY. If a damaged cord is found, have it repaired by a qualified service technician at an authorized service facility. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is required, do not connect the equipment-grounding conductor to a live terminal. Repair/replace damaged or worn cords immediately. Be constantly aware of the cord location and keep it well away from the rotating blade.

35.POLARIZED PLUGS. To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Warning:

USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST AND ASBESTOS. Direct particles away from face and body. Always operate tool in a well-ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with the dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/ OSHA approved respiratory protection appropriate for dust exposure, and wash exposed areas with soap and water.

1⁄2” 6 Amp Dual Purpose Hammer Drill

Operator’s Manual

GHD1260

Page 3 Page 5
Page 4
Image 4
Genesis Advanced Technologies GHD1260 manuel dutilisation English
Page 3 Page 5

GHD1260 specifications

Genesis Advanced Technologies has made a significant mark in the world of high-quality audio equipment, and the GHD1260 headphones stand as a testament to their commitment to excellence. Designed for both audiophiles and casual listeners alike, these headphones boast an array of features and technologies that elevate the listening experience to new heights.

One of the standout characteristics of the GHD1260 is its exceptional sound quality. The headphones employ advanced driver technology, allowing for an expansive soundstage and precise audio reproduction across the frequency spectrum. The 60mm dynamic drivers deliver powerful bass response while maintaining clarity in mids and highs. This balanced sound signature makes the GHD1260 versatile enough for various music genres, from classical to electronic.

Comfort is another key aspect of the GHD1260. The headphones are designed with ergonomics in mind, featuring plush ear cushions and an adjustable headband that ensures a secure yet comfortable fit. Whether you’re enjoying a long listening session at home or on the go, the lightweight design minimizes fatigue, enabling extended use without discomfort.

In terms of build quality, the GHD1260 is crafted using premium materials. The sturdy construction not only adds durability but also contributes to the acoustic performance, reducing unwanted resonance. The sleek finish and modern aesthetic make these headphones an attractive accessory for any music lover.

Connectivity options further enhance the usability of the GHD1260. The headphones include both wired and wireless capabilities, with Bluetooth support for hassle-free listening without the constraints of cables. The battery life is impressive, offering multiple hours of playtime on a single charge, perfect for those who are constantly on the move.

Furthermore, the GHD1260 features intuitive controls, allowing users to manage playback and take calls seamlessly. The integration of a built-in microphone adds functionality, making these headphones suitable for hands-free communication.

In summary, Genesis Advanced Technologies GHD1260 headphones combine superior sound quality, comfort, and robust build materials with advanced connectivity options and user-friendly features. They cater to the needs of any audio enthusiast, ensuring an immersive and enjoyable listening experience that stands out in today's competitive audio market.
Top Page Image Contents