Manuals / Genie / Lawn and Garden / Utility Vehicle

Genie GTH-636 manual Steering, Transmission, Controls And Instruments

Models: GTH-636

1 58

Download 58 pages 51.12 Kb

Page 33

STEERING

CONTROLS AND INSTRUMENTS

STEERING

In addition to the steering wheel, the machine has another steering control, the steering selector switch.

B

The steering selector switch (B) is a three-position switch. The three positions are: 4-wheel, 2-wheel , and oblique. Switch positions are selected and function as follows:

4-WHEEL	Handle right of center
2-WHEEL	Handle directly centered
OBLIQUE (CRAB)	Handle left of center

CAUTION

Before changing steering selections, make sure all four wheels are in line. Failure to align the wheels to the proper settings before changing steering positions may cause haphazard steering. This may result in injury to personnel and/or damage to the machine or property.

BRAKE ON

PUMP OFF

SWAY

CONTROL

RY

HEADLIGHT HEATER

LICS

TRANSMISSION

The transmission control (C) has one lever that controls both directional and speed requirements. It is located on the left side of the steering column.

To shift into Forward gear gently pull the lever toward you and move the lever upward.

To shift into Neutral move the lever to the center position.

To shift into Reverse gear gently pull the lever toward you and move the lever downward.

To shift into a lower speed rotate the lever clockwise.

To shift into a higher speed rotate the lever counter-clockwise.

When shifting the transmission from forward to reverse while the machine is in motion the transmission control (C) must be in 1st or 2nd gear only.

	Forward / 1st	Low speed/High torque	C
	Forward / 2nd	Medium speed/Medium torque	C
	Forward / 2nd	Medium speed/Medium torque
	Forward / 3rd	High speed/Low torque

BRAKE ON

PUMP OFF

SWAY

CONTROL

RY

HEADLIGHT HEATER

LICS

3 - 9

Image 33

Genie GTH-636 manual Steering, Transmission, Controls And Instruments

Contents

Operator’s Manual with Maintenance InformationGTH-636 First Edition Second Printing Part NoSECTION SECTION SECTION SECTION SECTION SECTION TABLE OF CONTENTSSECTION ROUGH TERRAIN FORK LIFT SAFETY SECTION 1 - ROUGH TERRAIN FORK LIFT SAFETY TABLE OF CONTENTSTHIS SYMBOL MEANS YOUR SAFETY IS ROUGH TERRAIN FORK LIFT SAFETYINTRODUCTION INVOLVED! READ, UNDERSTAND ANDROUGH TERRAIN FORK LIFT SAFETY STANDARDS AND SYMBOLSSYMBOLS STANDARDSSAFETY TRAINING AND KNOWLEDGEROUGH TERRAIN FORK LIFT SAFETY ROUGH TERRAIN FORK LIFT SAFETY OPERATORS RESPONSIBILITIESROUGH TERRAIN FORK LIFT SAFETY MANAGEMENTS RESPONSIBILITIESROUGH TERRAIN FORK LIFT SAFETY MAINTENANCE AND REPAIRROUGH TERRAIN FORK LIFT SAFETY OPERATION SAFETYROUGH TERRAIN FORK LIFT SAFETY OPERATION SAFETY13.Lifting Loads ROUGH TERRAIN FORK LIFT SAFETY OPERATION SAFETY18.Traveling on slopes/grades ROUGH TERRAIN FORK LIFT SAFETY SECTION GENERAL SAFETY TABLE OF CONTENTS SECTION 2 - GENERAL SAFETYGeneral Safety Procedures Proper Load Chart UseGENERAL SAFETY PROCEDURES GENERAL SAFETYSAFETY ALERT SYMBOL THE OPERATORHAND HOLDS AND STEPS WELDING PRECAUTIONSREFUELING GENERAL SAFETYSERVICE TIRES SAFELY HYDRAULIC SAFETYFLUIDS UNDER PRESSURE GENERAL SAFETYBOOM SAFETY PRACTICE SAFE MAINTENANCEUSE SEAT BELT GENERAL SAFETYDANGER AVOID ELECTRICAL POWER LINESGENERAL SAFETY GENERAL SAFETY PROCEDURESJUMP STARTING JUMP STARTINGGENERAL SAFETY GENERAL SAFETY PROPER LOAD CHART USEPROPER LOAD CHART USE GENERAL SAFETYSECTION CONTROLS AND INSTRUMENTS TABLE OF CONTENTS SECTION 3 - CONTROLS AND INSTRUMENTSOPERATORS COMPARTMENT CONTROLS AND INSTRUMENTSCONTROLS AND INSTRUMENTS JOYSTICK CONTROL FUNCTIONSA - Boom Down B - Boom Up C - Boom Out D - Boom InJOYSTICK CONTROL FUNCTIONS BUTTON PUSHED CONTROLS AND INSTRUMENTSA - Tilt Down B - Tilt Back SERVICE BRAKES PARKING BRAKECONTROLS AND INSTRUMENTS CONTROLS AND INSTRUMENTS FRAME SWAY CONTROLHYDRAULIC PUMP DESTROKE BUTTON GAUGESCONTROLS AND INSTRUMENTS DANGERSTEERING TRANSMISSIONCONTROLS AND INSTRUMENTS CONTROLS AND INSTRUMENTS SECTION OPERATION TABLE OF CONTENTS SECTION 4 - OPERATIONOPERATION OPERATION AND SAFETY GUIDELINESOPERATION BEFORE STARTING THE ENGINEOPERATION STARTING THE ENGINE DANGERDANGER DANGEROPERATION STARTING THE ENGINEOPERATION BEFORE OPERATING THE FORKLIFTBEFORE OPERATING THE FORKLIFT OPERATIONOPERATION BEFORE OPERATING THE FORKLIFT DANGERBEFORE OPERATING THE FORKLIFT DANGER OPERATIONOPERATION TRANSPORTING A LOADOPERATION TRANSPORTING A LOADSlower speeds should be used whenever transporting a load. Always bring the machine to a complete stop before reversing the transmission control lever A. Failure to do so can result in damage to the load, the machine and/or bystanders PLACING A LOAD WARNINGB OPERATIONDANGER PLACING A LOAD OPERATIONDANGER SECTION MAINTENANCE PROCEDURES TABLE OF CONTENTS SECTION 5 - MAINTENANCE PROCEDURESGeneral Safety Practices Daily MaintenanceMAINTENANCE PROCEDURES GENERAL SAFETY PRACTICESBEFORE SERVICING MAINTENANCE PROCEDURES FLUID UNDER PRESSUREGENERAL SAFETY PRACTICES HYDRAULIC SAFETYMAINTENANCE PROCEDURES DAILY MAINTENANCESCHEDULEDMAINTENANCE PERFORM ENGINE MAINTENANCEDAILY MAINTENANCE MAINTENANCE PROCEDURESDANGER CHECK HYDRAULIC OIL LEVELSECTION MATERIAL SAFETY DATA TABLE OF CONTENTS SECTION 6 - MATERIAL SAFETY DATAMaterial Safety Data Sheets California Proposition 65 WarningsMATERIAL SAFETY DATA SHEETS MSDS MATERIAL SAFETY DATACALIFORNIA PROPOSITION 65 WARNINGS MATERIAL SAFETY DATAWash hands after handling