Integrated Peripherals, Raid | Gigabyte GA-K8VT800-RH manual

2-3	Integrated Peripherals

			CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
				Integrated Peripherals
	IDE DMA transfer access			[Enabled]		Item Help
	OnChip IDE Channel 0			[Enabled]		Menu Level`
	OnChip IDE Channel 1			[Enabled]
	OnChip Serial ATA			[Enabled]
	SATA Mode			[RAID]
	AC97 Audio			[Auto]
	USB 1.1 Controller			[Enabled]
	USB 2.0 Controller			[Enabled]
	USB Keyboard Support			[Disabled]
	USB Mouse Support			[Disabled]
	Onboard H/W LAN			[Enabled]
	OnBoard LAN Boot ROM			[Disabled]
	Onboard FDC Controller			[Enabled]
	Onboard Serial Port 1			[3F8/IRQ4]
	Onboard Serial Port 2			[2F8/IRQ3]
	UART Mode Select			[Normal]
x	UR2 Duplex Mode			Half
	Onboard Parallel Port			[378/IRQ7]
	Parallel Port Mode			[SPP]
	Midi Port Address			[Disabled]
x	Midi Port IRQ			10
KLJI: Move		Enter: Select		+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values			F6: Fail-Safe Defaults	F7: Optimized Defaults

	IDE DMA transfer access
	Enabled		Enable IDE DMA transfer access. (Default value)
	Disabled		Disable this function.
	OnChip IDE Channel0
	Enabled		Enable onboard 1st channel IDE port.(Default value)
	Disabled		Disable onboard 1st channel IDE port.
	OnChip IDE Channel1
	Enabled		Enable onboard 2nd channel IDE port.(Default value)
	Disabled		Disable onboard 2nd channel IDE port.
	OnChip Serial ATA
	Enabled		Enable VT8237R / VT8237R+ Serial ATA support.(Default value)
	Disabled		Disable this function.
	SATA Mode
	RAID		Set onboard SATA mode to RAID.(Default value)
	IDE		Set onboard SATA mode to IDE.
	AC97 Audio
	Auto		Autodetect onboard AC'97 audio function. (Default value)
	Disabled		Disable this function.
	USB 1.1 Controller
	Disabled		Disable USB 1.1 controller.
	Enabled		Enable USB 1.1 controller. (Default value)

English

- 35 -

BIOS Setup

Image 35

Gigabyte GA-K8VT800-RH user manual Integrated Peripherals, Raid

Contents

GA-K8VT800-RH Motherboard Product Manual Classification Copyright Table of Contents Drivers Installation Item Checklist K8VT800-GA -RH GA-K8VT800-RH Motherboard Layout Block Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-Warranty CPU Feature Summary Use of licensed Award Bios Installation of the CPU Installation of the CPU and Heatsink Installation of the Heatsink Installation of Memory DDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1 / IDE2 IDE Connector FDD FDD Connector Pwrled SATA0/ SATA1 Serial ATA Connector Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel Connector Surcen Surround Center Connector Spdifio Spdif In / Out Connector 15 IR USB1 / FUSB2 Front USB Connector Clrcmos Clear Cmos Battery English English Main Menu Status Page Setup Menu / Option Page Setup Menu Main Menu For example Bios Ver. E8 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User Password IDE Channel 2/3 Master Standard Cmos FeaturesTime IDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Base Memory Drive A/Drive BHalt on Memory Password Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot Device RAID Integrated Peripherals USB Keyboard Support OnBoard LAN Boot ROMUart Mode Select USB 2.0 Controller Midi Port Address UR2 Duplex ModeParallel Port Mode Onboard Parallel Port Acpi OS Power Management Setup Modem Ring Resume Resume by AlarmPME Event Wake Up INT PnP/PCI Configurations Current CPU/SYSTEM FAN Speed RPM Current CPU TemperaturePC Health Status Current VoltageV Vcore / DDR25V / +3.3V / +12V Frequency/Voltage Control Dimm OverVoltage control Load Fail-Safe DefaultsTop Performance Set Supervisor/User Password Load Optimized Defaults Exit Without Saving Save & Exit Setup English Install Chipset Drivers Drivers Installation Software Information Software Application Contact Us Hardware Information English Unique Software Utilities Xpress Recovery IntroductionWhat is Xpress Recovery ? How to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/N Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutility Steps Using the Q-FlashTMutility You can repeat to Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screen Congratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM Utility English RAID Levels Serial ATA Bios Setting Utility Introduction Entering the RAID Bios Setup Configuring the VIA VT8237R / VT8237R+ RAID Bios Create RAID Array Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete a RAID array Delete Array¡G Installing the RAID drivers 4 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and Settings Channel Audio Setup English Surround-Kit connector Spdif cable connector English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English Taiwan Headquarters Contact Us Gigabyte Global Service System