PART | R0108A | ||||
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 1 | Frame | 51 | 1 | Return Spring |
2 | 1 | Upright | 52 | 1 | Magnet Guide |
3 | 1 | Front Stabilizer | 53 | 6 | M8 Washer |
4 | 1 | Rear Stabilizer | 54 | 1 | “C” Magnet |
5 | 1 | Console | 55 | 1 | Motor |
6 | 1 | Left Side Shield | 56 | 1 | Belt |
7 | 1 | Right Side Shield | 57 | 2 | Hub |
8 | 1 | Left Pedal Disc | 58 | 1 | Small Snap Ring |
9 | 1 | Left Handlebar | 59 | 1 | M5 x 40mm Screw |
10 | 1 | Right Handlebar | 60 | 2 | M6 Nut |
11 | 2 | Foam Grip | 61 | 4 | M5 Nylon Locknut |
12 | 2 | Pedal | 62 | 4 | M5 x 12mm Bolt |
13 | 1 | Upright Endcap | 63 | 2 | M10 x 83mm Button Screw |
14 | 1 | Left Pedal Arm | 64 | 1 | M8 x 41mm Bolt |
15 | 1 | Mast | 65 | 2 | Adjustment Bracket Screw |
16 | 4 | Pedal Post | 66 | 16 | M4 x 16mm Screw |
17 | 2 | Adjustment Pin | 67 | 2 | M8 x 70mm Button Bolt |
18 | 4 | Pedal Arm Bushing | 68 | 4 | Flywheel Screw |
19 | 2 | Adjustment Spring | 69 | 1 | Reed Switch Clamp |
20 | 2 | Adjustment Bracket | 70 | 1 | Idler Screw |
21 | 2 | Snap Ring | 71 | 2 | Handlebar Endcap |
22 | 2 | M8 x 25mm Patch Screw | 72 | 1 | Water Bottle Holder |
23 | 2 | Handlebar Cap | 73 | 1 | M6 x 16mm Screw |
24 | 6 | Handlebar Bushing | 74 | 4 | M4 x 38mm Screw |
25 | 2 | Handlebar Spacer | 75 | 1 | Right Pedal Arm |
26 | 2 | Upright Spacer | 76 | 2 | M4 x 22mm Screw |
27 | 2 | M10 x 59mm Bolt Set | 77 | 1 | Reed Switch |
28 | 4 | Leg Bushing | 78 | 1 | Reed Switch Bracket |
29 | 4 | M10 Nylon Locknut | 79 | 2 | Handlebar Leg |
30 | 1 | Pillow Block | 80 | 8 | M8 x 22mm Button Screw |
31 | 1 | Idler | 81 | 1 | Pivot Axle |
32 | 2 | Wheel | 82 | 8 | Cover Screw |
33 | 2 | M10 x 45mm Button Bolt | 83 | 2 | M8 Split Washer |
34 | 2 | M10 x 75mm Carriage Bolt | 84 | 4 | M8 x 16mm Button Screw |
35 | 4 | Stabilizer Endcap | 85 | 1 | Resistance Cable |
36 | 1 | Left Crank Arm | 86 | 1 | Upper Wire Harness |
37 | 1 | Idler Bracket | 87 | 1 | Lower Wire Harness |
38 | 1 | Right Crank Arm | 88 | 2 | Pedal Arm Sleeve |
39 | 1 | Crank | 89 | 2 | M3 x 12mm Screw |
40 | 2 | Crank Bearing | 90 | 4 | Motor Washer |
41 | 1 | Flywheel | 91 | 2 | Wave Washer |
42 | 4 | Large Snap Ring | 92 | 2 | Inner Pedal Arm Sleeve |
43 | 1 | Magnet | 93 | 2 | M6 Washer |
44 | 1 | Flywheel Spacer | 94 | 2 | M10 Split Washer |
45 | 2 | Adjustment Knob | 95 | 1 | Extension Wire Harness |
46 | 7 | M8 Nylon Locknut | 96 | 2 | Pedal Arm Endcap |
47 | 2 | Crank Screw | 97 | 1 | Right Pedal Disc |
48 | 2 | Hub Cover | * | – | Hex Key |
49 | 1 | M6 x 8mm Screw | * | – | Grease Packet |
50 | 4 | M8 x 45mm Button Bolt | * | – | User’s Manual |
Note: Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts. *These parts are not illustrated.
17
