Graco A5220, A3930, 2794 warranty TroubleShooting

TroubleShooting

DO NOT ATTEMPT to modify the unit. Any modifications to the transmitter and/or receiver can void the opera- tor’s authority to operate the equipment.

Pairing Parent Units and Child Units

Most problems have a simple solution. First, check that:

•Power is turned ON for both units

•Both units are plugged in (or batteries are fresh in Nursery Unit and fully charged in Parent Unit)

•Electrical outlet works

•Volume is turned up on Parent Unit

•Parent Unit is in range of the Nursery Unit

No Sound

•Battery dead or weak — replace or use AC adapter.

•AC adapter not properly connected — check the connec- tions.

•Nursery Unit covered or blocked — remove the obstruc- tion.

Weak Sound

•Nursery Unit too far from baby — move closer.

•Large objects blocking the signal — try repositioning Nursery Unit.

•Volume setting too low — turn it up.

Static

•Interference from other electrical equipment — eliminate cause of static (TVs, mixers, computers, fans, fluorescent lights, light dimmers, etc.)

•Parent Unit too far from Nursery Unit — move them closer.

•Significant amount of obstructions between Parent Unit and Nursery Unit such as walls, ceilings & buildings. Try moving the Nursery Unit to another part of the room.

•Change channel on Nursery Unit.

Shrill Sound (Feedback)

•Nursery Unit and Parent Unit too close together — move them farther apart.

•Volume set too high — lower the volume.

To ensure privacy, your two Parent Units are paired with your two Nursery Units at the factory. Your Parent Units will not work with any other Nursery Units.

If a Parent Unit won’t lock onto a Nursery Unit, or you purchased a new Nursery Unit, follow the procedure below to pair the Parent Units and Nursery Units. If you purchased a new Parent Unit, skip Step 1. The new Parent Unit is ready to pair with your Nursery Units.

1. Erase the Pairing from the Parent Unit

•Turn the Parent Unit off.

•Hold the Volume Down Button on the Parent Unit while press- ing the On/Off Button. Continue to hold the Volume Down Button until you hear a single beep and all of the yellow Sound Lights illuminate briefly.

•Release the Volume Down Button.

•Press and hold the Volume Down Button again.

•Within 2 seconds you will hear a beep. Release the Volume Down Button. All of the yellow Sound Lights and the red Loss Connection LED will be lit. The Parent Unit is ready to pair with both nursery units.

2. Pair the Parent Unit with Nursery Unit 1

•Place Nursery Unit 1 in the same room, five (5) feet (1.5 meters) away from the Parent Unit.

•Turn on Nursery Unit 1 using the On/Off Button on the side. The green power light should come on.

•Within a few seconds, the Parent Unit will find Nursery Unit 1. The yellow Sound Lights will shut off and the Parent Unit will beep. The Parent Unit is now paired with Nursery Unit 1.

•The green Sound Lights will be lit. The Parent Unit is ready to pair with Nursery Unit 2.

3.Pair the Parent Unit with Nursery Unit 2

•Place Nursery Unit 2 in the same room, five (5) feet (1.5 meters) away from the Parent Unit.

•Turn on Nursery Unit 2 using the On/Off Button on the side. The green power light should come on.

•Within a few seconds, the Parent Unit will find Nursery Unit 2. The green Sound Lights will shut off and the Parent Unit will beep. The Parent Unit is now paired with Nursery Unit 2.

•The Parent Unit will begin monitoring normally.

4.Repeat this procedure if you need to pair another Parent Unit with the Nursery Units

Nothing happened when I turned on the Nursery Unit. What do I do?

•First try turning the Nursery Unit off, and then on again.

•If the Parent Unit still does not pair with the Nursery Unit, press the Channel Button on the Nursery Unit, then turn the Nursery Unit off, and then on again.

6