LC-1000 Lube System Controller

14540

OPERATION

When power is applied, the green “POWER LED”lights and the LC-1000 counts down alternately from the programmed “OFF/ON” Times/Counts to zero.

In the “ON” (Monitor) mode, the ” PUMP LED” lights. The pump is activated and both the “ON and “RUN” icons are displayed. If the programmed number of cycle switch transitions (1/2 cycles) are received be- fore expiration of the “ON” (Monitor) period, the PUMP OUTPUT, “PUMP” LED, “ON” and “RUN” icons turn off and the “OFF” icon will display. If the programmed number of cycle switch transitions (1/2 cycles) are not received before expiration of the “ON” (Monitor) period, a “Fault” will be registered. This suspends pump operation, turns off the ” PUMP” LED, the “ON and “RUN” icons, turns on the red “FAULT” LED and closes the fault output contacts.

If a pulsed output to the pump is required, a “PUMP ON” time may be programmed from 0 to 99 seconds. Setting this value to zero will provide a steady state output. “PUMP OFF” is fixed at 3 seconds.

The “RUN” icon will display anytime the pump out- put is energized. During pulsed pump operation, the “RUN” icon will flash on and off in sequence with the pump. During continuous running, the “RUN” icon will not flash.

The Controller is programmed to retain the Time/Count in memory when power is turned off. This feature pre- vents excessive lubrication in start/stop applications and retains information for cycle to be completed when power is restored.

CHANGING SETTINGS

From the Timer display mode, pressing the “PRGM” button will allow you to review or change between the set “ON” (Monitor), “OFF”, “CYCLE, “PUMP” (Pulsed On Time) and “DISPLAY” modes. When in the pro- gramming mode, the icons/digits will blink. When in the display mode, the icons/digits do not blink.

1.To set a new “ON” (Monitor) Time/Count, press the “PRGM” key until the “ON” icon blinks. The current “ON” (Monitor) Time/Count will be displayed.

a)Press the “ENTER” key. The “ON” (Monitor) Time/Count digit will blink.

b)Change the value using the S key and X key.

c)Press the “ENTER” key to accept the new value. The “SEC/MIN/HR/CNT” icon will blink

d)Press “ENTER” to accept the time base or the S key to scroll through the timing choices.

e)Press “ENTER” to complete the process (Note: Monitor period is normally set 2 times the actual time required for the pump to satisfy the system cycle requirements).

2.The “OFF” icon will now be blinking.

a)Repeat above process until all “OFF”

options have been programmed.

b)Press “ENTER” to accept the new values.

3.The “CYCLE” icon will now be blinking

a)Press “ENTER” and the cycle value

(1/2 cycles) will blink.

b)Using the S and X keys set the cycle value as follows:

Series Progressive:

...............02 (1 divider cycle),

04 (2 divider cycles), 06 (3 divider cycles), etc.

Dual Line:

01 (half cycle) 02 (full cycle)

Piston Distributor or Injector:

01

c)Press “ENTER” to register the new value.

4.The “PUMP” icon will now blink.

a)Press “ENTER” again and the pump pulsed “ON” time will blink.

b)Using the S key and X key, set the value (seconds) as follows:

Self-Cycling Pump

 

 

(Motor Driven, or Reciprocating Barrel):

00

Single Shot Pump

 

 

(Piston Distributor, or Injector):

00

Single Shot Pump

 

 

(Recycle for Series Progressive):

03 to 10

c) Press "ENTER" to accept the new values.

NOTE: In the Recycle mode, PUMP “OFF” time is fixed at 3 seconds. Press “ENTER” to register the new value and return to the “DISPLAY” mode.

NOTE: Scrolling through the modes using the“PRGM” key only will allow the review of the current settings without changing any of the values or timing. It is recommended that programming not be attempted while a lube cycle is in process. After making any change in settings, activate a manual run to initiate the change.

NOTE: Programming examples for specific types of systems are shown on pages 5, 6 and 7.

MANUAL RUN / RESET

A manual-run lubrication cycle may be initiated by pressing the manual run button, located on the left underside of the unit, OR by shorting terminals 14 and 15 together, such as with a remote push-button momentary switch. Manual run may also be initiated by pressing S and "ENTER" keys together. Manul run is also used to reset the controlelr and to clear faults.

Page 4

Page 3 Page 5
Page 4
Image 4
Graco LC-1000 specifications Operation, Changing Settings, Manual RUN / Reset, Series Progressive
Page 3 Page 5

LC-1000 specifications

The Graco LC-1000, a flagship advancement in the world of paint sprayers, has garnered attention for its blend of performance, versatility, and user-friendly design. Engineered for both professionals and DIY enthusiasts, this sprayer excels in various applications, from small touch-up jobs to large-scale projects.

One of the standout features of the Graco LC-1000 is its advanced airless technology. This system allows for a smooth, consistent spray without the need for air compressors. The powerful motor ensures a high-performance output, offering the ability to spray at high pressure and producing a firmer, finer finish. The LC-1000 is capable of handling a wide variety of materials, including paints, stains, and sealers, making it suitable for both interior and exterior use.

Another key characteristic of the Graco LC-1000 is its Compact and Lightweight Design. Weighing in at just over 15 pounds, this sprayer is portable and easy to maneuver. The compact form factor allows for effortless storage and transport, making it an ideal choice for professionals who require mobility on the job site.

The LC-1000 features a QuickChange Tip system, enabling users to easily switch between different spray tips for various applications. This feature greatly enhances efficiency, as it allows for quick adjustments based on the project's requirements. Additionally, the sprayer's variable pressure control lets users customize the output for different surfaces and materials, ensuring optimal coverage and finish.

Equipped with the Graco SmartControl technology, the LC-1000 maintains a consistent spray pattern and pressure, which is crucial for achieving a professional-quality finish. The technology also features a digital display that provides real-time feedback, allowing users to monitor their settings and make immediate adjustments as needed.

Furthermore, the Graco LC-1000 is designed with user safety and convenience in mind. The integrated cleaning system simplifies the maintenance process, making it easier for users to clean the unit after each use. Moreover, the sprayer’s ergonomic handle and lightweight design reduce user fatigue, promoting prolonged use without discomfort.

In summary, the Graco LC-1000 stands out as a powerful, versatile paint sprayer equipped with advanced technology and features. Its user-friendly design, portability, and exceptional performance make it a top choice for anyone looking to achieve a flawless finish on their painting projects. Whether you're a seasoned professional or a weekend warrior, the Graco LC-1000 is engineered to meet your painting needs efficiently and effectively.
Top Page Image Contents