Greenheck Fan 474754 installation manual Installation

Filter Quantities

Unit	Safety Filter	Safety Filter
	Quantity	Quantity
Size
	(2 ft. tall x 2 ft. wide)	(2 ft. tall x 1 ft. wide)
02-03	1	1
02-04	2	0
02-05	2	1
02-06	3	0
04-03	2	2
04-04	4	0
04-05	4	2
04-06	6	0
04-07	6	2
04-08	8	0
04-09	8	2
06-03	3	3
06-04	6	0
06-05	6	3
06-06	9	0
06-07	9	3
06-08	12	0
06-09	12	3

Remote Mounted Detergent Dispenser

A 55 gallon remote mounted detergent dispenser is included as part of the electrostatic collector self-wash system. Included as part of the 55 gallon dispenser assembly is a solenoid valve, pressure gauge, ball valve, y strainer, and backflow preventer. The detergent dispenser must be mounted indoors on a solid, level foundation, as close to the cabinet assembly as possible, and in a freeze protected location accessible to maintenance personnel. The 1/2 inch line from the detergent dispenser must be connected to the water supply line within 5 feet of the precipitator. Refer to the PLUMBING section for details on plumbing connections.

Remote Mounted System Control Panel and Power Pack (2 pieces)

The system control panel allows the user to interface with the unit and controls operation as well as monitors wash and other functions. The Power Pack contains a power transformer and works in conjunction with the System Control Panel and the unit’s high voltage ionizer cells. The System Control Panel should be mounted in an area easily accessible to daily operational staff. The Power Pack should be mounted as close as possible to the System Control Panel and both should be mounted as close to the cabinet assembly as possible. Allow adequate room from the face of the panels for door swing clearance and servicing.

High Voltage Cable

High voltage cable is supplied to connect the ionizer/ collector sections of the precipitator to the ionizer and collector terminals in the Power Pack. The red cable (50 ft supplied) is used for the ionizer and the blue cable (50 ft supplied) is used for the collector. Refer to the ELECTRICAL section for details on wiring.

Installation

Rigging/Placing Equipment

1.The unit is furnished with lifting lugs at the four corners and along the length as necessary.

2.Lift into place using all the lifting lugs.

3.Field weight will vary depending upon final selections such as fan type, accessories, etc. Approximate weights are shown in the table below.

Unit Size	Approximate	Approximate
	Weight (lbs)	Weight (kg)
02-03	3100	1409
02-04	3620	1645
02-05	4025	1830
02-06	4280	1945
04-03	4000	1818
04-04	4580	2082
04-05	5200	2364
04-06	5700	2591
04-07	6420	2918
04-08	7080	3218
04-09	7560	3436
06-03	5200	2364
06-04	6140	2791
06-05	6800	3091
06-06	7325	3330
06-07	8275	3761
06-08	8800	4000
06-09	9510	4350

4.The unit can be positioned on a base or curb suitable for this purpose.

5.The unit must be anchored to its base/curb.

6.Alternatively, the unit may be suspended from an adequate overhead structure, using suitable undercarriage or hanging rods (by others). If the unit is suspended by hanging rods, minimum 1/2 inch (12.7 mm) diameter threaded rod is to be used. All hanger brackets/lifting lugs must be used to ensure proper support of the unit. The unit must also be hung level to ensure proper operation.

7.A service clearance of 42 inches must be provided on the access door side of the unit.

8.A minimum 18 inch clearance must be maintained between this unit and any combustible material.

4Grease Grabber™ Power Play Kitchen Exhaust Pollution Control System