![Application Data](/images/new-backgrounds/67457/6745711x1.webp)
Application Data
Damper Sleeve Dimensional Data
The drawings below and corresponding table show the position of the
The standard location of a damper mounted in a factory sleeve ("A" dimension) is shown below. The damper can be posi- tioned at other locations within a range of 6 in. (152mm) to 12 in. (305mm) for the "A" dimension.
11/2 in. max.
|
|
| 33/4 in. |
| 6 in. | Varies |
|
|
|
| 53/8 in. |
LH | RH |
|
|
| Right hand drive is shown | A | 5 in. |
| Left hand drive available upon request |
|
|
Sleeve Length
in. (mm) | "A" Dimension | ||
|
| ||
Standard | Maximum | ||
| |||
|
|
| |
All Dampers* | 7 3/16 in. (183) | 12 (305) | |
|
|
| |
When Height is | 12 (305) | 12 (305) | |
11 in. (279) or less |
|
| |
with OCI |
|
| |
|
|
|
*With the exception of dampers 10 in. high (254mm) or less.
NOTE: Entire damper frame is not required to be installed within the wall.
|
|
| T* | Actuators and Accessories | |||
|
|
|
|
|
|
| Space Envelopes |
S |
|
|
|
|
| Externally mounted actuators always require space out- | |
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| side of the damper sleeve. The “S” dimension illustrates |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| the clearance required for various available actuators. |
On dampers less than 18 in. (457mm) high, actuators may also require clearances above and/or below the sleeve. “B” and “T” dimensions are worst case clearance require- ments for some dampers less than 18 in. (457mm) high. All damper sizes under 18 in. (457mm) high do not require these worst case clearances. If space availability above or below the damper sleeve is limited, each damper size should be individually evaluated.
B*
Actuator |
| B* |
| T* | S |
Type/Model |
|
|
|
|
|
| With OCI |
| With OCI |
| |
|
|
|
| ||
|
|
|
|
|
|
|
| 120 Volt AC |
|
| |
|
|
|
|
| |
ML4XXX Series Honeywell | 5 | 1/4 in. (133mm) |
| 3/4 in. (19mm) | 6 in. (152mm) |
|
|
|
|
| |
MS4XXX Series Honeywell | 6 in. (152mm) |
| 3/8 in. (10mm) | 6 in. (152mm) | |
|
|
|
|
| |
MS4120 Series Honeywell | 6 in. (152mm) |
| 3/8 in. (10mm) | 6 in. (152mm) | |
|
|
|
|
|
|
|
| 24 Volt AC |
|
| |
|
|
|
|
| |
ML8XXX Series Honeywell | 5 | 1/4 in. (133mm) |
| 3/4 in. (19mm) | 6 in. (152mm) |
|
|
|
|
| |
MS8XXX Series Honeywell | 6 in. (152mm) |
| 3/8 in. (10mm) | 6 in. (152mm) | |
|
|
|
|
| |
MS8120 Series Honeywell | 6 in. (152mm) |
| 3/8 in. (10mm) | 6 in. (152mm) | |
|
|
|
|
| |
|
| Pneumatic (psi) |
| ||
|
|
|
| ||
1 in. (25mm) |
| 6 1/4 in. (159mm) | 6 1/2 in. (165mm) | ||
|
|
|
|
|
|
2 | 3/8 in. (60mm) |
| 12 1/8 in. (308mm) | 9 1/4 in. (235mm) | |
|
|
|
|
|
|
3 | 3/4 in. (95mm) |
| 16 1/2 in. (419mm) | 10 in. (254mm) | |
|
|
|
|
|
|
* For dampers 18 in. (457mm) or more in height these dimensions are 0 in. .