Duct Installation
Bottom Inlet Duct Connection
The end of the duct
Option 1: t/PJTPMBUJPOEBNQFSJOSPPGDVSC t#PUUPNJOMFUPOCZQBTTBJSQMFOVN
Duct |
|
|
| Roof Curb |
|
|
|
|
|
|
|
|
|
|
Option 2: t8JUIJTPMBUJPOEBNQFSJOSPPGDVSC
Adapter Tray
Isolation Damper
Duct
Duct Connection to Curb
Side or End Duct Connection
t7FLUPS)PS7FLUPS)4 t8JUICZQBTTBJSQMFOVN
NOTE
Plenum is provided with removable side or end panels, allowing the proper duct connection.
Duct flange and gasketing by
others
Bypass Air
Plenum
Roof Curb
Duct to Bypass Air Plenum
Stack Extensions
Systems with multiple stack extensions require all sections assembled and installed on site between the main fan body and the discharge cone. Each section has guy wire attachment brackets located on the upper end of each section. The order sections are installed in are universal. Gasketing (3/16 x 1/2 inch with sticky back) is provided and is to be installed between each joining section.
Guy wires are required on system with multiple stack extensions. Location of connections, wiring and anchorage is determined by a structural engineer.
System Assembly
NOTE
When installing each section, be certain to rig each section separately using the lifting lugs provided.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Gasket |
|
|
|
|
|
| Bolt and Washer | ||||||||||
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
| Detail | |||||||
Gasket |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5/16 inch | ||||||||||||
|
|
|
|
| |||||||||||||
|
|
|
|
|
| ||||||||||||
|
|
|
|
| |||||||||||||
|
|
|
|
|
| Gasket | |||||||||||
|
|
|
|
|
|
5/16 inch
Gasket
1.Mount roof curb to roof deck in accordance with local codes.
2.Install
3.Place the bypass air plenum (BAP) onto the previously installed gasket and secured roof curb. If a BAP is not provided for the unit, skip to Step 5.
4.Install
5.Place the curb cap of the fan housing onto the gasket and BAP or onto roof curb if BAP is not provided. Attach the curb cap using the provided
6.Install the final nozzle subassemblies as shown in the submittal drawing. Align flange bolt holes and fasten sections using the 316 stainless steel bolts, washers, and lock washers provided.
7.Follow electrical connection and
Laboratory Exhaust System 5
®