Drink Strength Adjustment for Model PIC3E or PIC33AE
when equipped with remote adjust knobs behind drip tray (Refer to Figure C)
1. Dispense a drink to determine if drink is too strong or too weak.
2. Remove drip tray.
3. Using a flat head screwdriver, adjust individual dispense heads by rotating appropriate adjustment knob. Clockwise rotation will result in a stronger drink and counterclockwise rotation will result in a weaker drink.
4.Dispense a drink to determine if drink strength is acceptable, repeat adjustment steps until desired drink strength is achieved.
NOTE: Water flow rate is factory preset at approximately 24mL (0.80 ounces) per second.
Figure C
Drink Strength Adjustment for Model PIC2J & PIC3J (Refer to Figure D)
Tool required: #2 Flat Head screwdriver
1.Dispense a drink to determine if drink is too strong, weak or if portion size is correct.
2.Turn off power to machine at power switch.
3.Drink strength and portion size controls will be found behind the drain tray. (Refer to Figure D) For portion size adjustment, turn dial clockwise to increase dispense volume. To decrease volume turn dial counterclockwise. For drink strength adjustment turn dial clockwise to increase drink strength. To decrease strength turn dial counterclockwise. Turn on power to machine and
dispense a drink to determine if drink strength or portion is acceptable. If drink strength or portion is not acceptable, turn off power to machine and repeat adjustment steps until desired drink strength or portion is achieved.
Note: Clockwise rotation will result in a stronger drink and | DRINK STRENGTH |
|
counterclockwise will result in a weaker drink. |
| |
ADJUSTMENT |
| |
Note: Water flow rate is factory preset at approximately | TURN DIAL CLOCKWISE TO |
|
INCREASE DRINK STRENGTH |
| |
0.80 ounces per second. | COUNTERCLOCKWISE TO | Figure D |
DECREASE STRENGTH | ||
|
*To adjust flow rate, remove left side upper panel. Use flat head screwdriver and turn knob on respective dump valve.
WARNING: Do not adjust flow rate above the factory setting to prevent funnel overflow.
Cleaning
CAUTION: When cleaning the unit, do not use cleansers, liquid bleach, powders or any other substance that contains
chlorine. These products promote corrosion of stainless steel and plastic parts. Use of these products will void the warranty.
DAILY
1.Empty the drip pan as needed and wash daily in a solution of dish detergent.
2.Rinse out the whipper chambers by placing the rinse switch (located on the right of the dispensing valves when the door is open) in the “ON” position. Dispense one to two cups until the water is clean. Short bursts of dispensing may also help clean the chambers more effectively. When completed, return the rinse switch to the “OFF” position.
3.Remove the hoppers and refill with product.
Crathco® Powdered Beverage Dispensers
Mixing Funnel Shroud
Water Inlet Fitting
Water Inlet Pipe
Funnel
Mixing Funnel
|
|
|
|
|
|
|
|
|
| Whipper Chamber | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
Whipper Base |
|
|
|
| ||||||||
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Motor Shaft |
|
|
|
| ||||||
|
|
|
|
|
|
|
| |||||
|
| Whipper Base Seal |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Whipper |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Whipper Blade |
|
| Dispense Nozzle |
| ||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure E
Page 7