Spindle Height | |
Controls |
|
I]Z he^cYaZ ]Z^\]i ^h X]Vc\ZY Wn jcadX`^c\ i]Z | |
he^cYaZ adX` aZkZg VcY jh^c\ i]Z XdVghZ [ZZY | |
aZkZgh dg i]Z [^cZ [ZZY `cdW Figure 12 # I]Z | |
he^cYaZ]Z^\]ihXVaZ^cY^XViZhi]Zhe^cYaZ]Z^\]i# | |
;^cZ;ZZY 8dVghZ | |
AdX`@cdW | ;ZZY |
| AZkZg |
He^cYaZ |
|
AdX` |
|
AZkZg |
|
Figure 12. He^cYaZXdcigdah# |
|
Changing spindle position using the coarse feed levers
1.JcadX`i]Zhe^cYaZadX`aZkZgVcYaddhZci]Z [^cZ[ZZYadX``cdW#
2.EjaaYdlcdcVcnd[i]ZXdVghZ[ZZYaZkZghid adlZgdggV^hZi]Zhe^cYaZ#DWhZgkZi]ZhXVaZ dci]Z]ZVYhidX`[VXZeaViZidbdc^idgbdkZ" bZci^c^cX]Zhdgb^aa^bZiZgh#I]ZbVm^bjb gVc\Zd[igVkZa^h)(¿)#
3.AdX`i]Zhe^cYaZadX`aZkZgid]daYi]Zhe^cYaZ ^cVeVgi^XjaVgedh^i^dc^[ndjX]ddhZ#
Tip: Milling with the spindle fully extended can cause tool chatter. For maximum spindle rigidity when milling, it is better to keep the spindle retracted into the headstock as far as possible with the spindle lock lever locked, and the fine feed lock knob tightened.
<%*&.B^aa$9g^aa$IVee^c\BVX]^cZ
Changing the spindle position using the fine feed dial
1. JcadX`i]Zhe^cYaZadX`aZkZgVcYi^\]iZci]Z | |
[^cZ[ZZYadX``cdW# |
|
2. GdiViZ i]Z [^cZ [ZZY `cdW id adlZg dg gV^hZ | |
i]Zhe^cYaZ^chbVaa^cXgZbZcih#DWhZgkZi]Z | |
hXVaZ dc i]Z `cdW id bdc^idg bdkZbZci ^c | |
i]djhVcYi]hd[Vc^cX] Figure 13 # |
|
;^cZ;ZZY 8dVghZ | |
AdX`@cdW | ;ZZY |
| AZkZg |
He^cYaZ |
|
AdX` |
|
AZkZg |
|
;^cZ;ZZY |
|
@cdW |
|
Figure 13. He^cYaZ[^cZ[ZZYXdcigdah# | |
3.AdX`i]Zhe^cYaZadX`aZkZgid]daYi]Zhe^cYaZ ^cVeVgi^XjaVgedh^i^dc^[ndjX]ddhZ#
Tip: Milling with the spindle fully extended can cause tool chatter. For maximum spindle rigidity when milling, it is better to keep the spindle retracted into the headstock as far as possible with the spindle lock lever locked, and the fine feed lock knob tightened.
"&,"
