G0528 Sliding Router Table -13-
Components Needed: Qty
Stand Legs .........................................................4
Diagonal Supports ..............................................2
Tray ....................................................................1
Carriage Bolts 5⁄16"-18 x 1⁄2" ...............................32
Flat Washers 5⁄16" ..............................................32
Lock Washers 5⁄16" ............................................32
Hex Nuts 5⁄16"-18 ...............................................32
Tools Needed:
12mm Wrench or Socket ....................................1
To assemble the stand:
1. Secure the stand legs to the table cross sup-
ports with 12 carriage bolts, 12 flat washers,
12 lock washers, and 12 hex nuts. Note—
The stand leg with the switch cut-out should
be facing the front of the machine.
2. Secure the tray to the stand legs with 16 car-
riage bolts, 16 flat washers, 16 lock washers,
and 16 hex nuts.
3. Secure the diagonal supports (Figure 7) to
the stand legs and the tray with 4 carriage
bolts, 4 flat washers, 4 lock washers, and 4
hex nuts.
Figure 7. Table diagonal support positions.
Components Needed: Qty
Spacers ..............................................................2
Phillips Head Screws 1⁄4"-20 x 11⁄2" .....................2
Flat Washers 1⁄4" .................................................4
Hex Nuts 1⁄4"-20 ..................................................2
Tools Needed:
Phillips Head Screwdriver ..................................1
Adjustable Wrench .............................................1
To assemble the braces:
1. Slide a washer over the screws.
2. Slide the screws through each brace.
3. Thread the screws through the spacers.
Note—Allow just enough of a gap between
the washers and the spacers for the table
braces to slide freely.
4. Secure the screw/spacer assemblies to the
stand with the washers and the hex nuts.
Figure 8. Assembling the table braces.
SPECIFICATIONS
FAILURE TO FOLLOW THESE WARNINGS WILL RESULT IN SERIOUS PERSONAL INJURY:
1. READ AND UNDERSTAND THE ROUTER AND ROUTER
TABLE MANUAL BEFORE STARTING THE MACHINE.
2. ALWAYS WEAR EYE PROTECTION AND A RESPIRATOR.
3. PLUG POWER CORD INTO GROUNDED OUTLET ONLY.
4.
ALWAYS KEEP HANDS OUT OF THE CUTTER PATH.
5. KEEP ALL GUARDS IN PLACE AT ALL TIMES.
6.
DO NOT WEAR LOOSE CLOTHING, GLOVES OR JEWELRY.
SECURE LONG HAIR AND BUTTON ALL LONG SLEEVE
SHIRTS.
7. DISCONNECT POWER PRIOR TO SERVICING, CHANGING
CUTTERS OR ADJUSTING FENCE AND MITER GAUGE.
8. DO NOT EXPOSE TO RAIN OR DAMPNESS.
9. DO NOT OPERATE UNDER THE INFLUENCE OF DRUGS
OR ALCOHOL.
10. MAKE SURE MACHINE IS PROPERLY ADJUSTED AND SET
UP CORRECTLY BEFORE STARTING MOTOR.
11. BEFORE STARTING MACHINE, MAKE CERTAIN IT RESTS
SECURELY ON FLAT, LEVEL GROUND.
12. KNOW HOW TO AVOID RISK OF KICKBACK.
13. DO NOT REMOVE JAMMED OR CUT-OFF WORKPIECE
WHILE CUTTER IS TURNING.
14. BEFORE STARTING MACHINE, MAKE SURE CUTTER IS
INSTALLED CORRECTLY AND PROPERLY TIGHTENED.
15. NEVER MAKE FREE-HAND CUTS. ALWAYS USE THE
FENCE OR MITER.
16. BEFORE STARTING MACHINE, ALWAYS CHECK FEED
DIRECTION.
17. MAKE SURE CUTTER HAS COME TO A COMPLETE STOP
PRIOR TO MAKING ANY ADJUSTMENTS.
18. NEVER ATTEMPT TO REMOVE TOO MUCH MATERIAL IN
ONE PASS.
G0528
SLIDING ROUTER TABLE
UNIVERSAL ROUTER MOUNTING SYSTEM
TABLE INSERT DIAMETERS: 1-1/8", 2-5/16"
TABLE COUNTERBORE: 3-1/2"
DUST PORT: 2-1/2"
STAND: POWDER-COATED STEEL
WEIGHT: 125 LBS.
Date
Serial Number
Manufactured for Grizzly in Taiwan
READ AND UNDERSTAND THE
ROUTER AND ROUTER TABLE
OPERATOR'S MANUAL BEFORE
USING THIS MACHINE. FAILURE
TO FOLLOW OPERATING
INSTRUCTIONS WILL RESULT IN
DEATH OR SERIOUS PERSONAL
INJURY.