
Installing Faceplate
To install the faceplate:
1. | 9>H8DCC:8IA6I=:;GDBEDL:G |
2. >chZgii]Z^cYZm^c\e^c^ciddcZd[i]Z^cYZm" | |
| ^c\]daZhVcYgdiViZi]Zhe^cYaZjci^ai]Ze^c |
| Zc\V\Zh id egZkZci i]Z he^cYaZ [gdb ijgc^c\ |
| l]^aZndji^\]iZci]Z[VXZeaViZ!Vhh]dlc^c |
| Figure 26# |
| ;VXZeaViZHZi |
| HXgZl&d[' |
Figure 26.AdX`^c\he^cYaZl^i]^cYZm^c\e^cVcY | |
| [VXZeaViZhZihXgZladXVi^dc# |
3. | I]gZVYi]Z[VXZeaViZdcidi]Zhe^cYaZjci^a^i |
| ^hhcj\# |
4. Jh^c\i]Z^cXajYZY)bb]ZmlgZcX]!i^\]iZc | |
| i]ZildhZihXgZlhVadc\i]Z^ch^YZY^VbZiZg |
| d[ i]Z [VXZeaViZ id hZXjgZ ^i id i]Z he^cYaZ |
| hZZFigure 26# |
To prevent the faceplate and workpiece sep- arating from the spindle during operation, the headstock faceplate MUST be firmly threaded onto the spindle and secured in place by fully tightening the two faceplate set screws. If these instructions are not properly performed, serious personal injury could occur.
Note: To remove the faceplate, disconnect the lathe from the power source and perform the steps above in reverse.
BdYZa<%,((B[\#H^cXZ&%$&&
Changing Speed
Ranges
I]Z BdYZa <%,(( ]Vh ejaaZn WZai Xdc[^\jgVi^dc egdk^YZYildheZZYgVc\ZhhZZFigure 27#
He^cYaZ
6 | 2=^\]GVc\Z |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| |||
| ((%"('%%GEB | 6 |
|
|
|
| |||
|
|
|
|
| |||||
7 | 2AdlGVc\Z |
|
|
|
| ||||
|
|
|
|
|
|
| |||
7 | |||||||||
| &%%"&'%%GEB |
|
|
|
|
|
|
| |
|
| Bdidg |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 27.HeZZYgVc\ZWZaiedh^i^dch#
Note: To maximize spindle torque, use the low spindle speed range for spindle speeds of 1200 RPM or less.
GZ[Zg id i]Z heZZY gZXdbbZcYVi^dch X]Vgi ^c Figure 28idX]ddhZi]ZVeegdeg^ViZGEB[dgndjg deZgVi^dc#I]ZcX]ddhZi]ZheZZYgVc\Zi]Vil^aa ^cXajYZi]ZhZaZXiZYGEB#
Diameter | Roughing | General | Finishing |
of Work- | RPM | Cutting | RPM |
piece |
| RPM |
|
JcYZg' | &*'% | ('%% | ('%% |
'¶) | ,+% | &+%% | |
)¶+ | *&% | &+*% | |
&')% | |||
(%% | +*% | &%%% | |
&%¶&' | '** | *)% | |
&'¶&) | ''% | )+% | ,&% |
&)¶&+ | &.% | )%% | +'% |
Figure 28.BdYZa<%,((heZZY gZXdbbZcYVi^dch#
To change speed ranges:
1. 9>H8DCC:8IA6I=:;GDBEDL:G
"'*"