Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD. Make |
| 16. REDUCE THE RISK OF UNINTENTION- |
| ||||||||||
sure your extension cord is in good condi- |
| AL STARTING. On machines with mag- |
| ||||||||||
tion. Conductor size should be in accor- |
| netic contact starting switches there is a |
| ||||||||||
dance with the chart below. The amperage |
| risk of starting if the machine is bumped or |
| ||||||||||
rating should be listed on the motor or tool |
| jarred. Always disconnect from power |
| ||||||||||
nameplate. An undersized cord will cause |
| source before adjusting or servicing. Make |
| ||||||||||
a drop in line voltage resulting in loss of |
| sure switch is in OFF position before recon- |
| ||||||||||
power and overheating. Your extension |
| necting. |
|
|
|
|
| ||||||
cord must also contain a ground wire and |
|
|
|
|
|
|
| ||||||
plug pin. Always repair or replace exten- |
| 17. MANY WOODWORKING TOOLS CAN |
| ||||||||||
sion cords if they become damaged. |
| “KICKBACK” THE WORKPIECE toward |
| ||||||||||
| Minimum Gauge for Extension Cords |
| the operator if not handled properly. Know |
| |||||||||
|
| what conditions can create “kickback” and |
| ||||||||||
|
|
|
|
|
|
|
| know how to avoid them. Read the manual |
| ||||
|
| LENGTH | |||||||||||
|
|
| accompanying the machine thoroughly. |
|
| ||||||||
| AMP RATING | 25ft |
| 50ft |
| 100ft |
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||||
| 18 |
| 16 |
| 16 |
| 18. CHECK DAMAGED PARTS. Before fur- |
| |||||
| 18 |
| 16 |
| 14 |
| ther use of the tool, a guard or other part |
| |||||
| 16 |
| 16 |
| 14 |
| that is damaged should be carefully |
| |||||
|
|
|
|
|
|
|
| checked to determine that it will operate |
| ||||
| 14 |
| 12 |
| 12 |
|
| ||||||
|
|
|
| properly and perform its intended function. |
| ||||||||
| 12 |
| 12 |
| 10 |
|
| ||||||
|
|
|
| Check for alignment of moving parts, bind- |
| ||||||||
|
| 10 |
| 10 |
| No |
|
| |||||
|
|
|
| ing of moving parts, breakage of parts, |
| ||||||||
10. WEAR PROPER APPAREL. Do not wear |
| mounting, and any other conditions that |
| ||||||||||
| may affect its operation. A guard or other |
| |||||||||||
loose clothing, gloves, neckties, rings, |
| part that is damaged should be properly |
| ||||||||||
bracelets, or other jewelry which may get |
| repaired or replaced. |
|
|
|
| |||||||
caught in moving parts. |
|
|
|
|
|
|
| ||||||
is recommended. Wear protective hair cov- |
| 19. NEVER LEAVE TOOL RUNNING UNAT- |
| ||||||||||
ering to contain long hair. |
|
|
|
| TENDED. TURN POWER OFF. Do not |
| |||||||
11. ALWAYS USE SAFETY GLASSES. Also |
| leave tool until it comes to a complete stop. |
| ||||||||||
|
|
|
|
|
|
| |||||||
use face or dust mask if cutting operation is |
| 20. NEVER OPERATE A MACHINE WHEN |
| ||||||||||
dusty. Everyday eyeglasses only have impact |
| TIRED, OR UNDER THE INFLUENCE OF |
| ||||||||||
resistant lenses, they are NOT safety glasses. |
| DRUGS OR ALCOHOL. Full mental alert- |
| ||||||||||
12. SECURE WORK. Use clamps or a vise to hold |
| ness is required at all times when running |
| ||||||||||
| a machine. |
|
|
|
|
| |||||||
| work when practical. It’s safer than using your |
|
|
|
|
|
|
| |||||
| hand and frees both hands to operate tool. |
| 21. NEVER ALLOW UNSUPERVISED OR |
| |||||||||
|
|
|
|
|
|
|
|
| |||||
13. DO NOT OVERREACH. Keep proper foot- |
| INEXPERIENCED | PERSONEL | TO |
| ||||||||
| OPERATE THE MACHINE. Make | sure |
| ||||||||||
| ing and balance at all times. |
|
|
|
|
| |||||||
|
|
|
|
| any instructions you give in regards to |
| |||||||
|
|
|
|
|
|
|
|
| |||||
14. MAINTAIN TOOLS WITH CARE. Keep |
| machine operation are approved, correct, |
| ||||||||||
| safe, and clearly understood. |
|
| ||||||||||
tools sharp and clean for best and safest |
|
|
| ||||||||||
|
|
|
|
|
|
| |||||||
performance. Follow instructions for lubri- |
| 22. IF AT ANY TIME YOU ARE EXPERIENC- |
| ||||||||||
cating and changing accessories. |
|
|
|
| |||||||||
|
|
| ING DIFFICULTIES performing the intend- |
| |||||||||
|
|
|
|
|
|
|
|
| |||||
15. USE RECOMMENDED ACCESSORIES. |
| ed operation, | stop | using | the machine! |
| |||||||
| Then contact | our service | department or |
| |||||||||
Consult the owner’s manual for | recom- |
|
| ||||||||||
| ask a qualified expert how the operation |
| |||||||||||
mended accessories. The use of improper |
|
| |||||||||||
| should be performed. |
|
|
|
| ||||||||
accessories may cause risk of injury. |
|
|
|
|
| ||||||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
G8690 Variable Speed Wood Lathe |
|
|
|
|
|
|
|
|
| ||||
