MODEL H0614/H0615 |
HAND CRANK |
HOSE REEL |
INSTRUCTIONS |
Mounting |
To reduce the risk of injury when using this | Use 3⁄8" hardware through the four holes of the |
hose reel base to firmly secure the assembly to a | |
tool: | convenient and stable location. |
•Make sure the incoming air pressure
does not exceed the maximum rating | Assembly | |
of 300 PSI. Otherwise the fittings could | ||
1. Insert the handle shaft through the handle, | ||
crack or explode. | ||
• Protect your eyes by wearing safety | then secure the assembly to the crank with | |
glasses or a face shield when assem- | the lock nut and flat washer, as shown in | |
bling and using this hose reel. | Figure 2. |
•Pressurized air may cause injury to
exposed body parts. Never expose any | Swivel |
|
|
part of your body to pressurized air. | Connector |
| Handle |
• Make sure the hose reel is firmly mounted |
|
|
|
|
|
| |
to a stable surface before pressurizing. |
|
|
|
Specifications |
|
|
|
|
| ||||||||||
Max. Incoming Air Pressure | 300 PSI |
|
|
|
| ||||||||||
Max. Hose Length on Reel for H0614 | 100 ft. |
|
|
|
| ||||||||||
Max. Hose Length on Reel for H0615 | 50 ft. |
|
|
|
| ||||||||||
|
| Reel Hose |
| ||||||||||||
Air Fitting Size |
|
|
|
|
| 3⁄8" NPT |
|
|
| ||||||
|
|
|
|
|
|
| Connection |
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Inventory |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
| Figure 2. Assembly components (Model H0614 | ||||||||
Use the list below and Figure 1 to inventory the |
|
| shown). | ||||||||||||
contents of the shipping box. |
|
| Note: Use Teflon pipe tape or thread seal- | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Description |
|
|
|
|
| Qty |
| ant on all threaded connections. Also, do not | |||||||
|
|
|
|
|
| overtighten the connections or you may dam- | |||||||||
A. | Hose Reel Assembly (not shown) | 1 |
| ||||||||||||
| age the threads, resulting in leaks. | ||||||||||||||
B. Swivel Connector 3⁄8" x 3⁄8" NPT | 1 |
| |||||||||||||
|
|
|
| ||||||||||||
C. | Handle |
|
|
|
|
| 1 |
| 2. Install the swivel connector into the center | ||||||
D. | Handle Shaft | 1 |
| ||||||||||||
| axle on the opposite side from handle (see | ||||||||||||||
E. | Lock Nut | 1 |
| ||||||||||||
| Figure 2), then connect the incoming air sup- | ||||||||||||||
F. | Flat Washer 5⁄16" | 1 |
| ||||||||||||
| ply to it. | ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| 3. Connect the reel hose to the 3⁄8" reel hose | ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| C |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| connection shown in Figure 2. | ||
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
| B |
|
|
|
|
|
|
|
|
| 4. Turn the air pressure ON, then use soapy | |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| D |
|
| water to test for leaks. If any are found, turn | ||
|
|
| F |
| E |
|
|
|
| the air pressure OFF, relieve the pressure | |||||
|
|
|
|
|
|
|
|
|
|
|
|
| from the hose, then repair the leaks before | ||
|
|
|
|
|
|
|
|
|
|
|
| ||||
| Figure 1. Model H0614/H0615 small item |
| putting the hose reel into operation. | ||||||||||||
|
|
|
|
|
|
| inventory. |
|
|
|
|
| |||
