Hafler GX2300CE, GX2600CE manual BRIDGE MONO MODE GX2300/GX2600, 70V MONO MODE GX2300/GX2600

BRIDGE MONO MODE (GX2300/GX2600)

	70V
100v	4Ω
8Ω	2Ω	CH A
Load		Power	2300
	70V
100v	4Ω
8Ω	2Ω	CH B

		HP –			180˚–	Delay		—
	Crossover LP –				0˚–
		Full –				must
	CD EQ +0		2	6	Phase choose			300W
						one		2Ω – 8Ω
					0”-	only
		+10 dB			6”-	Audio GND
	Freq	500Hz –			12”-
					18”-	Chassis	Float
		800Hz –			24”-			+
CH A					30”-		—
IN	BIAMP STEREO				ON
		HP –			180˚–
	Crossover LP –				0˚–		+	+
		Full –			Phase
	CD EQ +0 2			6		Delay
		+10 dB			0”-
					6”-	must
	Freq	500Hz –			12”-	choose		300W—
					18”-
		800Hz –			24”-	one
					30”-	only	600W
CH B					ON	4Ω– 16Ω		2Ω – 8Ω
IN	(Mono)					Mono,70V,100V

Class 2 wiring

				-18-15-12
				-21	-9
				-24	-6
				-27	-3
	Channel A			-32
				-38
				OFF	0dB
signal	protect		Stereo Mono
				70V
				100V
				-18-15-12
clip		thermal		-21	-9
				-24	-6
				-27	-3
	Channel b			-32
				-38
				OFF	0dB

		A Division of
		Rockford Corp.
	®	Tempe, AZ 85281
	G X 2 3 0 0	Made in the U.S.A.
	300 W Stereo, 2Ω– 8Ω
For 70V, 100V, or Mono	600W Mono, 70V,100V

• Use CH B input

• Load across RED terminals

• Set load switches to one half load impedance

Attention: Utiliser un fusible de rechange de même type.

CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.

250W

250V T7A 115V~

50-60Hz

1.Connect signal from source to CH B input.

2.Stereo/Biamp switch not active-(Stereo/Mono switch overrides this switch when in mono/70V/100V mode).

3.Move Stereo/Mono switch to MONO mode.

4.Set load switches (8Ω/4Ω/2Ω) to 1/2 the actual load impedance. (16Ω/8Ω/4Ω) i.e. for a 4Ω speaker load,

select the 2Ω setting for both CH A and CH B Load Switches

5.Connect appropriate speaker load 16Ω/8Ω/4Ω across the red terminals of the 5-way binding posts.

6.CH B level control adjusts the mono output level. (1200W-GX2600, 600W-GX2300)

70V MONO MODE (GX2300/GX2600)

70V
100v 4Ω
8Ω	2Ω		CH A
Load			Power			2300
70V
100v 4Ω
8Ω	2Ω		CH B
100V		70V							100V	70V
	GX2300								GX2600
			HP –			180˚–	Delay		—
		Crossover LP –				0˚–
			Full –				must
		CD EQ +0		2	6	Phase choose			300W
							one		2Ω – 8Ω
						0”-	only
			+10 dB			6”-	Audio GND
		Freq	500Hz –			12”-
						18”-	Chassis	Float
			800Hz –			24”-			+
CH A						30”-		—
	BIAMP STEREO					ON
IN
			HP –			180˚–
		Crossover LP –				0˚–		+	+
			Full –			Phase
		CD EQ +0 2			6		Delay
			+10 dB			0”-
						6”-	must
		Freq	500Hz –			12”-	choose		300W—
						18”-
			800Hz –			24”-	one
						30”-	only	600W
CH B						ON	4Ω– 16Ω		2Ω – 8Ω
IN	(Mono)						Mono,70V,100V

Class 2 wiring

70 Volt

Transformer

			-18-15-12
			-21	-9
			-24	-6
			-27	-3
	Channel A		-32
			-38
			OFF	0dB
signal	protect	Stereo Mono
			70V
			100V
			-18-15-12
clip	thermal		-21	-9
			-24	-6
			-27	-3
	Channel b		-32
			-38
			OFF	0dB

	A Division of
	Rockford Corp.
®	Tempe, AZ 85281

GX 2 3 0 0 Made in the U.S.A. 300 W Stereo, 2Ω– 8Ω

For 70V, 100V, or Mono 600W Mono, 70V,100V

• Use CH B input

• Load across RED terminals

• Set load switches to one half load impedance

Attention: Utiliser un fusible de rechange de même type.

CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.

250W

250V T7A 115V~

50-60Hz

70 Volt	etc.
Transformer

Parallel Array

1.Connect signal from source to CH B input.

2.Stereo/Biamp switch not active (Stereo/Mono switch overrides this switch when in mono/70V/100V mode).

3.Move Stereo/Mono switch to 70V mode.

4.Select 70V load, both channels.

5.Connect parallel array of 70V transformer-equipped speakers across the red terminals of the 5-way binding posts. (1200W–GX2600, 600W–GX2300)

6.CH B input sensitivity controls 70V mono output level. Amplifier will clip at 70Vrms level.

– 20 –