BRIDGE MONO MODE (SR2300/SR2600)
| Load | Power |
|
|
| |
100V | 70V |
|
|
|
|
|
8Ω | 4Ω | 2Ω |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
100V | 70V |
|
|
|
|
|
8Ω | 4Ω | 2Ω |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| – 3 |
|
| — |
|
|
|
| + | – | + | |
|
|
|
|
|
| 300W | |
|
|
| 1 | 2 |
|
| 2Ω – 8Ω |
|
|
|
| Audio GND |
|
| |
|
|
|
| Chassis | Float |
|
|
CH A | BIAMP STEREO | CH A |
|
|
| — | + |
IN | OUT |
|
| 600W | |||
|
|
|
| 4Ω | – 16Ω | + |
|
|
|
|
| Mono,70V,100V | + | ||
|
|
| For 70V, 100V, or Mono |
|
| ||
|
|
| • Use CH B input |
|
| ||
|
|
| • Load across RED |
|
| ||
|
|
| terminals |
|
|
| |
|
|
| • Set load switches to one | 300W | |||
CH B |
| CH B | half load impedance |
| |||
|
|
|
|
| 2Ω – 8Ω | ||
IN | (Mono) | OUT |
|
|
|
| — |
S R 2 3 0 0
300 W Stereo, 2Ω – 8Ω
600W Mono, 70V,100V
Attention: Utiliser un fusible de rechange de même type.
CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.
250W 250V T7A
A Division of
Rockford Corp.
Tempe, AZ 85281
Made in the U.S.A.
1.Connect signal from source to CH B input.
2.Biamp/Stereo switch not
3.Move Stereo/Mono switch to MONO mode.
4.Set load switches (8Ω /4Ω /2Ω ) to 1/2 the actual load impedance. (16Ω /8Ω /4Ω ) i.e. for a 4Ω speaker load,
70V MONO MODE (SR2300/SR2600)
select the 2Ω setting for both CH A and CH B Load Switches
5.Connect appropriate speaker load 16Ω /8Ω /4Ω across the red terminals of the
6.CH B level control adjusts the mono output level.
|
|
|
|
|
|
|
|
|
|
|
|
| Load | Power | |||||||||
100V | 70V |
|
|
|
|
|
|
|
|
|
|
8Ω | 4Ω | 2Ω | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
100V | 70V |
|
|
|
|
|
|
|
|
|
|
8Ω | 4Ω | 2Ω | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
100V | 70V |
|
|
| 100V | 70V | |
| SR2300 |
|
|
| SR2600 |
| |
|
|
| – 3 |
|
| — |
|
|
|
| + | – | + |
| |
|
|
|
|
|
| ||
|
|
|
|
| 300W |
| |
|
|
| 1 2 |
|
| 2Ω – 8Ω |
|
|
|
| Audio GND |
|
|
| |
|
|
| Chassis | Float |
|
|
|
CH A |
| CH A |
|
| — | + |
|
IN | BIAMP STEREO OUT |
| 600W |
| |||
|
|
| 4Ω | – 16Ω | + |
|
|
|
|
| Mono,70V,100V | + |
| ||
|
|
| For 70V, 100V, or Mono |
|
|
| |
|
|
| • Use CH B input |
|
|
| |
|
|
| • Load across RED |
|
|
| |
|
|
| terminals |
|
|
|
|
|
|
| • Set load switches to one | 300W |
| ||
CH B |
| CH B | half load impedance |
|
| ||
|
|
|
| 2Ω – 8Ω |
| ||
IN | (Mono) | OUT |
|
|
| — |
|
S R 2 3 0 0
300 W Stereo, 2Ω – 8Ω
600W Mono, 70V,100V
Attention: Utiliser un fusible de rechange de même type.
CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.
250W 250V T7A
A Division of
Rockford Corp.
Tempe, AZ 85281
Made in the U.S.A.
70 Volt | 70 Volt |
Transformer | Transformer |
Parallel Array
etc.
1.Connect signal from source to CH B input.
2.Biamp/Stereo switch not active (Stereo/Mono switch overrides this switch when in mono/70V/100V mode).
3.Move Stereo/Mono switch to 70V mode.
4.Select 70V load, both channels.
5.Connect parallel array of 70V
6.CH B input sensitivity controls 70V mono output level. Amplifier will clip at 70Vrms level.
