100V MONO MODE (SR2300/SR2600)
|
|
|
|
|
|
|
|
|
|
|
|
| Load | Power | |||||||||
100V | 70V |
|
|
|
|
|
|
|
|
|
|
8Ω | 4Ω | 2Ω | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
100V | 70V |
|
|
|
|
|
|
|
|
|
|
8Ω | 4Ω | 2Ω | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
100V 70V
SR2300
CH A | BIAMP STEREO | CH A |
IN | OUT | |
CH B |
| CH B |
IN | (Mono) | OUT |
100V 70V
|
|
|
| SR2600 |
| – 3 |
|
| — |
| + | – | + | |
|
|
| ||
|
|
| 300W | |
1 | 2 |
|
| 2Ω – 8Ω |
| Audio GND |
|
| |
| Chassis | Float |
|
|
|
| 600W | — | + |
| 4Ω | – 16Ω | + |
|
| Mono,70V,100V | + | ||
For 70V, 100V, or Mono |
|
| ||
• Use CH B input |
|
| ||
• Load across RED |
|
| ||
terminals |
|
|
| |
• Set load switches to one | 300W | |||
half load impedance |
| 2Ω – 8Ω | ||
|
|
|
| — |
| A Division of |
| Rockford Corp. |
S R 2 3 0 0 | Tempe, AZ 85281 |
Made in the U.S.A. |
300 W Stereo, 2Ω – 8Ω
600W Mono, 70V,100V
Attention: Utiliser un fusible de rechange de même type.
CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.
250W 250V T7A
100 Volt
Transformer
1.Connect signal from source to CH B input.
2.Biamp/Stereo switch not active (Stereo/Mono switch overrides this switch when in mono/70V/100V mode).
3.Move Stereo/Mono switch to 100V mode.
4.Select 100V load, both channels.
70V STEREO MODE (SR2600 ONLY)
100 Volt | etc. | |
Transformer | ||
|
Parallel Array
5.Connect parallel array of 100V
6.CH B input sensitivity controls 100V mono output level.
Amplifier will clip at 100Vrms level.
|
|
|
|
|
|
|
|
|
|
|
|
| Load | Power | |||||||||
100V | 70V |
|
|
|
|
|
|
|
|
|
|
8Ω | 4Ω | 2Ω | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
100V | 70V |
|
|
|
|
|
|
|
|
|
|
8Ω | 4Ω | 2Ω | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
100V 70V
SR2600
CH A | BIAMP STEREO | CH A |
IN | OUT | |
CH B |
| CH B |
IN | (Mono) | OUT |
| – 3 |
|
| — |
| + | – | + | |
|
|
| ||
|
|
| 300W | |
1 | 2 |
|
| 2Ω – 8Ω |
| Audio GND |
|
| |
| Chassis | Float |
|
|
|
| 600W | — | + |
| 4Ω | – 16Ω | + |
|
| Mono,70V,100V | + | ||
For 70V, 100V, or Mono |
|
| ||
• Use CH B input |
|
| ||
• Load across RED |
|
| ||
terminals |
|
|
| |
• Set load switches to one | 300W | |||
half load impedance |
| 2Ω – 8Ω | ||
|
|
|
| — |
S R 2 3 0 0
300 W Stereo, 2Ω – 8Ω
600W Mono, 70V,100V
Attention: Utiliser un fusible de rechange de même type.
CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.
250W 250V T7A
A Division of
Rockford Corp.
Tempe, AZ 85281
Made in the U.S.A.
70 Volt | 70 Volt |
Transformer | Transformer |
| Parallel Array |
70 Volt | 70 Volt |
Transformer | Transformer |
etc.
etc.
1.Connect signal from source to both CH A and CH B inputs.
2.Move Biamp/Stereo switch to Stereo mode.
3.Move Stereo/Mono switch to Stereo mode.
4.Select 8Ω speaker load for each channel.
5.Connect parallel array of 70V
6.Adjust CH A and CH B level controls independently.