Install the water inlet hose
Confirm the water faucet
Reserve,Process,remain time digitron | "Power" button |
Water faucet,suitable | Water faucet,not suitable |
Outlet end surface
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1.
It displays
It displays remained reserve time (hour).
It displays total remained time (min). If the total time exceeds 99 minutes, it uses "A" on tens digit to represent100 minutes, and uses "b" to represent 110 minutes.E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation. (See to Page15)
Push the "power" button to switch on the power.
Under 
Push the "power" button to switch on the power. If the "start/pause" button is not pushed, the machine will switch off the power automatically after 5 minutes.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. |
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the |
four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise |
HT
LIG
(MINUTES) | FLASH |
WATER
POWER ON/OFF
it may leak water. See to Figure 3.) |
(HOURS LATER)
LEVEL 
Digital display
Fuzzy logic control
water inlet hose jointer
Slider
Screw
Sign plate
PROGRAM/RESERVE
10 water level selection
Screw knife
Lock level
water inlet hose
Figure 1
Bushing
Figure 2 | Figure 3 |
PROGRAM/RESERVE
button
Push down the program/ reserve button. You can select one program of ten which is
WATER LEVEL 
button
The washing machine can detect the laundries automatically. After detection,it will set the water level to suitable value among 4, 6, 8,and 10 automatically.
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 4 | Figure 5 | Figure 6 |
|
standard,soak heavy, gentle,save,cotton, single wash,rinse spin,single spin,tub clean, air dry;
Push the"program/ reserve" button to set the reserve wash program morethan two seconds continuously;
When the "reserve" function is activated, the indicator light of the program you have set will be off. The "reserve (hour)" and "time remain" indicator lights will be on;
During reserve procedure, push the "reserve" button to display the reserve mode.To change the running program or cancel the reserve setting, you need to switch off the power and make new selection;
You can also set water level by yourself. After the machine is started, it will not set water level automatically. You shall push thestart/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .
If save program is selected, it will display water level 2 . When water level 2 is reached in water filling, it will perform washing while filling water.When water level 3 is reached, it will change to normal washing.
During operation of wash and rinse program, you can push down the water level button to add water. When you release the button, or it reaches the overflow water level, the machine will stop adding water.
The water level decided may be different from actual value because of the different moisture level of the laundries.
Attention As | selecting the water level 1,3,5,7,9;the light |
is | flashing; |
As | selecting the water level 2,4,6,8,10;the light |
is | lighting; |
