Usingi process
Steps of using the operation buttons and description of the steps
|
|
|
|
|
| TIME REMAINED(MINUTE) |
|
|
MINUTES | MINUTES | TIMES | MINUTES |
|
| STANDARD |
| |
|
|
|
|
| ||||
|
|
|
|
|
| SILK | SAVE |
|
|
|
|
| nano wash |
| COTTON | BLANKET |
|
|
|
| MIN | TUB CLEAN | WOOLLEN |
| ||
|
|
|
|
| (18L) | RESERVE(HOURS LATER) |
|
|
Digital tub display |
|
|
|
|
|
|
|
|
10 water level selection |
|
|
|
|
|
| START | POWER |
12 mins quick wash |
|
|
|
|
|
| ON/OFF | |
S u p e r - p o w e r digi t a l int e l l ig e nt co n t ro l |
|
|
|
|
|
| PAUSE | |
|
|
|
|
|
|
| ||
SOAK | WASH | RINSE | SPIN | + |
| RESERVE | PROGRAM |
|
|
|
|
|
| WATER LEVEL |
|
|
Push the "POWER ON/OFF " button to switch on the power.
POWER
ON/OFF
2Push the "PROGRAM" button to select suitable automatic program.
Install the water inlet hose Before Usingi
Confirm the water faucet
water faucet, suitable |
|
|
|
| water faucet, not suitable |
| The exit end face of the faucet |
|
|
| |
|
|
| |||
|
|
|
|
|
|
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1.
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise it may leak water. See to Figure 3.)
PROGRAM
After switching on the power, the machine will set standard program automatically. To select other automatic 
program, push the "program" button till the relative indicator is on. Refer to the "program button" on Page
11 for the selection.
For instance: select "SAVE" program for laundries with small quantity
water inlet hose jointer
Slider
Screw
Nameplate
and light soil.
Page 11
Lock level | Screw knife |
|
Bushing
In selecting the standard program, the machine |
|
STANDARD | |
will execute fuzzy program to select water | SAVE |
SILK |
water inlet hose
Figure 1
Figure 2
Figure 3
and wash time according to the cloth and weight |
| |
| COTTON | BLANKET |
of the laundries. The full procedure is controlled |
| |
| TUB CLEAN | WOOLLEN |
automatically. |
|
|
Push the "SOAK","WASH", "RINSE" or "SPIN"button to select suitable procedure.
MINUTES MINUTES TIMES MINUTES
SOAK | WASH | RINSE | SPIN |
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet. See to Figure 5.
Remark: .Before twisting the fastening nut, the threading is 4mm above the upper surface of the nut. After twisting, the threading is less than 2mm above the upper surface of the nut. See to Figure 6
about 4mm after twisting
About above 2mm after twisting
Screw nut
Figure 4 | Figure 5 | Figure 6 |
12 | 5 |
