![](/images/new-backgrounds/1315271/31527125x1.webp)
stops working completely. The Carbon Brushes are located on each side of the Motor Housing. To do so, remove the two Brush Covers (3). Then, remove the two Carbon Brushes. If the Carbon Brushes are worn down more than 1/2, replace both Carbon Brushes. If, however, the Carbon Brushes are just dirty they may be cleaned by rubbing them with a pencil eraser. When installing the Carbon Brushes, make sure the carbon portion of the Carbon Brushes contact the Motor Armature, and that the springs face away from the Motor. Also, make sure the springs operate freely. After cleaning or replacement, replace the Brush Covers. NOTE: New Carbon Brushes tend to arc or spark when first used until they wear and conform to the Motor’s Armature.
(See Figure F, previous page.)
5. CAUTION! All maintenance, service, or repairs not listed in this manual are only to be attempted by a qualified service technician.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part # | Description | Qty. | Part # | Description | Qty. |
1 | Power Cord | 1 | 23 | Collector Bag | 1 |
2 | Cord Clamp | 1 | 24 | Clamp | 1 |
3 | Brush Cover | 2 | 25 | Inlet Cover | 1 |
4 | Carbon Brush | 2 | 26 | Safety Screen | 1 |
5 | Washer | 1 | 27 | Collector Body | 1 |
6 | Screw | 1 | 28 | Screw | 9 |
7 | Safety Key | 1 | 29 | Lock Washer | 9 |
8 | Power Switch | 1 | 30 | Hex Bolt | 4 |
9 | Screw | 2 | 31 | Lock Washer | 4 |
10 | Flat Washer | 2 | 32 | Machine Mounting Bracket | 1 |
11 | Switch Cover Plate | 1 | 33 | Hex Nut | 4 |
12 | Motor Mounting Bracket | 1 | 34 | Flat Washer | 8 |
13 | Shaft Key | 1 | 35 | Handle | 1 |
14 | Ground Conductor Cover | 1 | 36 | Cap Nut | 4 |
15 | Hex Screw | 4 | 37 | Lock Washer | 8 |
16 | Lock Washer | 4 | 38 | Hex Nut | 4 |
17 | Gasket | 1 | 39 | Caster | 4 |
18 | Collector Cover | 1 | 40 | End Cap | 1 |
19 | Gasket | 1 | 41 | Machine Base | 1 |
20 | Impeller | 1 |
|
|
|
21 | Washer | 1 |
|
|
|
22 | Hex Nut | 1 |
|
|
|
SKU 94029 | For technical questions, please call | Page 13 |