Harman-Kardon 210 owner manual Macro Programming, Press the AVR Selector f, Erasing Macro Commands

Programming the Remote

Macro Programming

Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the AVR 210’s remote con- trol. Once programmed, a macro will send out up to 19 different remote codes in a predeter- mined sequential order, enabling you to auto- mate the process of turning on your system, changing devices, or other common tasks. The AVR 210’s remote can store up to five separate macro command sequences: one that is associated with the Power On button a, and four more that are accessed by pressing the Macro buttons w.

1.Press the Mute button 38 and the Macro button w to be programmed or the Power On button a at the same time. Note that an Input Selector will light red, and the Program/SPL Indicator c will flash amber.

2.Enter the steps for the macro sequence by pressing the button for the actual command step. Although the macro may contain up to 19 steps, each button press, including those used to change devices, counts as a step. The Program/SPL Indicator c will flash green to confirm each button press as you enter commands.

NOTE: While entering commands for Power On/Off of any device during a macro sequence, press the Mute button 38 . DO NOT press the actual Power button.

3.When all the steps have been entered, press the Sleep button i to enter the commands. The red light under the Input Selectors ef will blink and then turn off.

Example: To program the Macro 1 button so that it turns on the AVR 210, TV and a Cable Box, follow these steps:

•Press the Macro 1 wand Mute 38 buttons at the same time and then release them.

•Note that the Program/SPL Indicator will flash amber.

•Press the AVR Selector f.

•Press the Mute button 38 to store the AVR 210’s power on command.

•Press the VID 2 Input Selector button eto indicate the next command is for “TV Power On.”

•Press the Mute button 38 to store the TV Power On Command.

•Press the VID 3 Input Selector button eto indicate the next command is for “Cable Power On.”

•Press the Mute button 38 to store the Cable Power On command.

•Press the Sleep/Channel Up button i to complete the process and store the macro sequence.

After following these steps, each time you press the Macro 1 button w, the remote will send the Power On/Off command.

Erasing Macro Commands

To remove the commands that have been pro- grammed into one of the Macro buttons, follow these steps:

1.Press the Mute button 38 and the Macro button w that contains the com- mands you wish to erase.

2.Note that the Program/SPL Indicator c will flash amber, and the LED under the AVR Selector f will turn red.

3.Within ten seconds, press the Surround

Mode Selector/Channel Down button j.

4.The red LED under the AVR Selector will go out, and the Program/SPL Indicator c will turn green and flash three times before it goes out.

5.When the Program/SPL Indicator c goes out, the Macro has been erased.

Programmed Device Functions

Once the AVR 210’s remote has been pro- grammed for the codes of other devices, press the appropriate Input Selector eto change the remote from controlling the AVR 210 to con- trolling the additional product. When you press any one of the selectors, it will briefly flash in red to indicate that you have changed the device being controlled.

When operating a device other than the AVR 210, the controls may not correspond exactly to the function printed on the remote

or button. Some commands, such as the volume control, are the same as they are with the AVR 210. Other buttons will change their function so that they correspond to a secondary label on the remote. For example, the Sleep and Surround mode selector buttons also func- tion as the Channel Up and Channel Down

1		2	3
4	5	6	7
8	9	10	11
	12	13	14
15	16	17	18
19	20	21	22

2324

25

26	27		28
	29
30			31
32	33	34	35
36	37	38	39
40	41	42	43
44	45	46	47
48	49	50	51
52	53	54	55
56	57		58

5960 61

62 63

210

34PROGRAMMING THE REMOTE