ADVANCED FUNCTIONS

Manual SPEAKER Setup

The AVR 760/AVR 660 is flexible and may be configured for most speakers, and to compensate for the acoustic characteristics of your room.

The EzSet/EQ II process automatically detects the capabilities of each speaker, and optimizes the AVR 760/AVR 660’s performance. If you are unable to run EzSet/EQ II calibration, or if you wish to make further adjustments, use the Manual Speaker Setup on-screen menus.

Before beginning, place your loudspeakers as explained in the Speaker Placement section, and connect them to the AVR. Consult the owner’s guide for the speakers or the manufacturer’s Web site for the frequency range specification. Although you may set the output levels “by ear,” an SPL (sound- pressure level) meter purchased at a local electronics store will provide greater accuracy.

Record your configuration settings in Tables A3 through A12 in the appendix for easy re-entry after a system reset, or if the AVR’s Master Power Switch is turned off or the unit is unplugged for more than four weeks.

NOTE: When using the AVR’s Speaker Setup menus, select a video output resolution of 720p or higher to view graphics that simplify configuration.

STEP ONE – Determine Speaker Crossover

Without using the EzSet/EQ II process, the AVR 760/AVR 660 can’t detect how many speakers you’ve connected to it; nor can it determine their capabilities. Consult the speaker’s technical specifications and locate the frequency response, usually given as a range, e.g., 100Hz – 20kHz (±3dB). Write down the lowest frequency that each of your main speakers is capable of playing (100Hz in the example) as the crossover in Table A3 in the appendix. This is not the same as the crossover frequency listed in the speaker’s specifications. For the subwoofer, write down the transducer size.

The receiver’s bass management determines which speakers will be used to play back the low-frequency (bass) portion of the source program. Sending the lowest notes to small satellite speakers won’t sound right, and may even damage the speaker. The highest notes may not be heard at all through the subwoofer.

With proper bass management, the AVR 760/AVR 660 divides the source signal at a crossover point. All information above the crossover point is played through the satellite speaker, and all information below the crossover point is played through the subwoofer. Each loudspeaker in your system performs at its best, delivering an enjoyable sound experience.

STEP TWO – Measure Speaker Distances

Ideally, all of your speakers would be placed in a circle, with the listening position at the center. However, you may have had to place some speakers a little further away from the listening position than others. Sounds that are supposed to arrive simultaneously from different speakers may blur, due to different arrival times.

Use the AVR’s Distance/Delay adjustment to compensate for real-world speaker placements.

Measure the distance from each speaker to the listening position, and write it down in Table A4 in the appendix. Even if all of your speakers are the same distance from the listening position, enter your speaker distances as described in Step Three.

STEP THREE – Manual Setup Menu

Now you are ready to program the receiver. Sit in the usual listening position and make the room as quiet as possible.

With the receiver and video display turned on, press the AVR Settings Button to display the menu system. Use the L Button to move the cursor to the Speaker Setup line, and press the OK Button to display the Speaker Setup menu. See Figure 21 in the Basic Manual.

If you have run the EzSet/EQ II process, the results were saved in one of the two listening positions (AVR 760 position 1+2, AVR 660 1 position). Adjust the Speaker Setup setting in the Audio Effects menu to activate the results for either position (AVR 660: 1 position) (see page 26-27 in the Basic Manual). To tweak the EzSet/EQ II results, or to configure the AVR from scratch, select Setup Listening Position 1 (AVR 760, AVR 660) or Setup Listening Position 2 (AVR 760). A screen similar to the one shown in Figure 28 will appear.

Figure 28 – Speaker Setup Position Menu

NOTE: All of the speaker setup submenus include the Back option, as shown at the bottom of Figure 28. To save the current settings, select the Back option.

To reconfigure the speakers from scratch, select the Reset option.

For best results, adjust the submenus in this order: Number of Speakers, Crossover (Size), Sub Mode, Distance and Level Adjust.

Number of Speakers

Move the cursor to the Number of Speakers line and press the OK Button. See Figure 29.

Figure 29 – Number of Speakers Menu

Program the correct setting for each speaker group: ON when the speakers are present in the system, and OFF for positions where no speakers are installed. The Front Left & Right speakers are always ON and may not be disabled. Any changes will be reflected in the total number of speakers displayed at the top of the screen.

6

Page 6
Image 6
Harman-Kardon AVR 760 Manual Speaker Setup, Step ONE Determine Speaker Crossover, Step TWO Measure Speaker Distances

AVR 660, AVR 760 specifications

Harman-Kardon has long been recognized as a leader in the home audio industry, and their AVR 760 and AVR 660 receivers exemplify this reputation. These models are designed to deliver high-quality audio and video performance for a rich entertainment experience, making them ideal additions to any home theater setup.

The Harman-Kardon AVR 760 is a powerful 7.1-channel receiver that offers an impressive 100 watts per channel. It features advanced audio technologies such as Dolby Atmos and DTS:X, which provide immersive, three-dimensional sound by allowing audio to move around the listener in a realistic manner. This capability enhances the viewing experience for movies, concerts, and games, immersing users in a surround sound environment.

Equipped with the latest HDMI technology, the AVR 760 supports 4K Ultra HD video, ensuring that users enjoy stunning picture quality with enhanced detail and clarity. The receiver includes multiple HDMI inputs and outputs, which allow seamless connectivity to various devices such as gaming consoles, Blu-ray players, and streaming devices. Additionally, HDR (High Dynamic Range) compatibility is supported, enhancing contrast and color presentation on compatible displays.

The AVR 660, while slightly lower in wattage at 80 watts per channel, offers similar capabilities and features that make it a strong contender in the home audio market. It also supports Dolby Atmos and DTS:X technologies, delivering a captivating audio experience. With its 7.1-channel configuration, the AVR 660 is designed to provide rich sound quality for home theater enthusiasts.

Both models come with built-in Wi-Fi and Bluetooth connectivity, allowing users to stream music directly from their smartphones or tablets. They also feature Spotify Connect, which facilitates easy access to music playlists. The receivers are compatible with various streaming services, enabling users to enjoy their favorite tracks effortlessly.

The user interface of both the AVR 760 and AVR 660 is intuitive, with an easy-to-navigate on-screen display that makes setup and configuration straightforward. Additionally, the receivers feature Multi-Room Audio functionality, allowing users to expand their audio experience beyond the main theater area by distributing sound throughout the home.

In conclusion, the Harman-Kardon AVR 760 and AVR 660 represent a perfect blend of power, advanced technology, and user-friendly features. Whether you’re a cinephile or a music lover, these receivers are engineered to elevate your home entertainment experience to new heights. With stunning audio and video capabilities, they stand as a testament to Harman-Kardon's commitment to quality and innovation in the world of audio equipment.