Venting

 

Non-combustible cover, one

 

side only. If two covers are

Hole with a minimum

used, each must be mounted

clearance of 18" (450 mm)

on non-combustible spacers

between connector and wall.

at least 7/8" (21mm) away

 

from the wall.

1" (25mm) Clearance

AN APPROVED CANADIAN

WALL PASS-THROUGH

Closest

Minimum 2" (50mm)

Combustible

Material

Clearance to Brick

 

Liner

Minimum 12"

 

(300mm) to Brick

 

 

 

Flue

Fire Clay

 

Thimble

 

 

 

Chimney

Chimney

 

 

Connector

Masonry Chimney Built to

NFPA 211 Specifications.

Minimum 12" (300mm) to Combustibles

AN APPROVED U.S.

WALL PASS-THROUGH

The Chimney

The TL300 must be installed into a chimney approved for use with solid-fuel appliances. In the U.S., the TL300 must be connected to (1) a prefabricated chimney complying with the requirements for Type HT chimneys in the Standard for Chimneys, Factory-Built, Residential Type and Building Heating Appliances, UL 103, or (2) a code-approved masonry chimney with a flue liner.

In Canada, the TL300 is listed for use with prefabricated chimneys tested and listed to the high temperature (650 degrees C) chimney standard, ULC S-629, or with a code approved masonry chimney.

Do not connect this unit to a chimney flue servicing another appliance.

NOTE: The restriction of not venting more than one appliance to the same flue applies to the U.S. specifically. While it is not recommended that you use the same chimney for more than one appliance, in Canada certain exceptions may be made. Be sure to contact your building code inspection official to see if this option is allowed in your area, and to find out the specific requirements for such an installation.

For mobile homes,(US only) the TL300 must only be installed with prefabricated chimney systems, including the installation components, tested to use in mobile homes; the diameter should match the diameter of the flue collar opening

The minimum recommended height for any chimney is 16 ft (4.8 m) above flue collar height. For non-mobile home installations, a round flue (either masonry or approved prefabricated), of either 6" (150 mm), 7" (180 mm) or 8" (200 mm) may be used. For square or rectangular masonry chimneys, nominal sizes of 8" x 8" or 8"x 12" (200mm x 200 mm, 200 mm x 300 mm) may be used.

Codes require that solid-fuel chimneys extend 3 ft (0.9

m) above the highest point at which they exit from the roof.

Then, the chimney must extend 2 ft.(6 m) above the highest

point within a 10 ft (3 m) radius. Thus, the 3 foot, 2 foot, 10

More Than 10 ft. (3m)

10 ft. (3m)

2 ft. (0.6m) min.

Ridge

Chimney

Height Necessary Above Any Roof Sur- face Within 10ft. (3m)

3ft. (0.9m) minimum above exit

point

foot rule: 3ft. - Above roof exit point

2ft. - Higher than anything within-

10ft. of the chimney.

The 3-foot, 2-foot, 10 foot rule

Harman TL300 11

Page 10 Page 12
Page 11
Image 11
Harman Stove Company TL300 manual Chimney, AN Approved Canadian Wall PASS-THROUGH
Page 10 Page 12

TL300 specifications

The Harman Stove Company TL300 is a standout choice for homeowners seeking an efficient and reliable home heating solution. This pellet stove is designed to deliver exceptional warmth and coziness with minimal environmental impact, making it a popular option among both first-time buyers and seasoned users.

One of the defining features of the TL300 is its high-efficiency design. With a thermal efficiency rating of over 85%, this stove maximizes heat output while minimizing fuel consumption. This efficiency not only translates into lower heating bills but also reduces the frequency of pellet replenishment, allowing for longer periods of uninterrupted warmth.

Equipped with Harman's patented Smart Control technology, the TL300 takes user convenience to the next level. This advanced system offers precise temperature control, allowing users to set and maintain their desired heating levels with remarkable accuracy. The user-friendly interface is intuitive, making it easy for anyone to operate. Additionally, Smart Control enables the integration of Wi-Fi capabilities, allowing homeowners to control the stove remotely via smartphone or tablet, ensuring that a warm and inviting atmosphere greets them upon return home.

The TL300's construction reflects Harman's commitment to quality. Built from durable materials, the stove is designed to withstand the rigors of regular use while maintaining an aesthetically pleasing appearance. The large glass viewing window not only provides a warm ambiance with its glowing flames but also enhances the visual appeal of any room.

Another notable characteristic of the TL300 is its environmentally friendly approach. The stove produces significantly lower emissions compared to traditional wood-burning stoves, making it an eco-conscious choice for modern living. Harman has also incorporated a self-cleaning feature, reducing maintenance efforts and keeping the unit running efficiently.

The TL300 is versatile, suitable for a variety of home sizes and layouts. With adjustable blower settings, users can customize the heat distribution according to their space's specific needs. Whether you want to heat a cozy living room or a more spacious area, the TL300 can adapt to your requirements.

In conclusion, the Harman Stove Company TL300 combines elegance, efficiency, and advanced technology to deliver an outstanding heating solution. With its high-efficiency performance, smart control capabilities, durable construction, and environmental benefits, this pellet stove is a smart addition to any home, ensuring comfort and warmth during the colder months.
Top Page Image Contents