OPERATING THE MOWER
Slopes | Grassbag |
To prevent engine damage do not use the mower on | Raise the rear deflector and lift the grassbag through the |
slopes greater than 20 degrees. (Refer fig.13) | handlebar and lower the rear deflector to rest against the |
| rear of the mower. |
Friction Disc
The cutterblade is driven by the engine via a friction disc to help prevent damage occurring to the engine crankshaft and cutting mechanism when a hidden
Height Of Cut
To adjust the height of cut: Grip the lever and pull side- ways to disengage it from the locking notch, then push forwards to lower or pull backwards to raise the height of cut. Finally release the lever at the required position and ensure it locks firmly into one of the seven setting notches.
Always select a height of cut to suit operating conditions. Aim to prevent engine overloading and blockages by avoiding low cuts in long grass conditions. Be prepared to make two cuts when the grass is long. (Refer fig.14)
Before Mowing
To prevent accidents, thoroughly inspect the area and remove all objects which when contacted by the mower cutterblade could become dangerous projec- tiles. Inspect the area for hidden obstructions which when contacted by the cutterblade could risk health and safety or result in damage to the mower. Remem- ber the location of these obstructions and ensure that you mow around them. (Refer fig.15)
To empty the grassbag, pour out the grass clippings and shake the grassbag vigorously to clean the airways. Good grass collection depends on good air flow through the grassbag. When collecting grass clippings it is important that the grassbag is emptied regularly to prevent block- ages and engine overloading. (Refer fig.16)
Without Grass Collection
Remove the grassbag and operate the mower with the
rear deflector in the closed position. (Refer fig.17)
Heavy Growth
Areas of heavy growth should be mown without collecting the clippings. If collection is required, first mow the area without the grassbag at the maximum height of cut setting. Allow the grass clippings to dry out and then mow the area at the maximum height of cut setting with the grassbag fitted. Reduce the height of cut and mow the area again as necessary until the required finish is obtained.
To prevent damage to your lawn do not remove more than one third of grass height in one cut. (Refer fig.18)
obstruction or overload is encountered. (Refer fig.19)
Always stop the engine when a hidden obstruction or excessive vibration is encountered. Disconnect the spark plug lead and examine the cutting mechanism. ALWAYS replace a damaged cutterblade - Refer to “Maintenance”.
Non Grassed Areas
When moving the mower across
Fig. 13 | Fig. 14 | Fig. 15 | Fig. 16 | Fig. 17 |
| Fig. 18 | Fig. 19 | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9
