PROBLEMSOLUTION

4.The walking belt is off-center or slips when walked on

a.If the walking belt is off-center, first re- move the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the allen wrench to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered.

a

b. If the walking belt slips when walked on,

 

 

 

 

b

 

first remove the key and UNPLUG THE

 

 

 

 

 

POWER CORD. Using the allen wrench,

 

 

 

turn both rear roller bolts clockwise 1/4 of a

 

 

 

turn. When the walking belt is correctly

 

 

 

tightened, you should be able to lift each

 

 

 

side of the walking belt 3 to 4 inches off the

 

 

 

walking platform. Be careful to keep the

 

 

 

walking belt centered. Plug in the power

 

 

 

 

 

 

cord, insert the key, and walk on the tread-

 

 

 

mill for a few minutes. Repeat until the walking belt is properly tightened.

5.The displays of the console do not func- tion properly

a. Remove the key from the console and UN-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a

 

 

 

 

 

 

 

 

 

 

 

 

 

PLUG THE POWER CORD. Next, remove

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/8”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the screws from the hood and carefully re-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

44

 

 

11

 

move the hood. Locate the Reed Switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(17) and the Magnet (12) on the left side of

 

 

 

 

17

 

 

 

 

 

 

 

 

the Pulley (11). Turn the Pulley until the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top

 

 

 

 

 

 

 

 

 

Magnet is aligned with the Reed Switch.

 

 

 

 

 

 

 

 

 

 

 

 

Make sure that the gap between the

 

 

View

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Magnet and the Reed Switch is about

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/8”. If necessary, loosen the indicated

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Screw (44) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood and run the treadmill for a few minutes to check for a correct speed reading.

26

Page 26
Image 26
Healthrider HRT15920 manual Walking belt is off-center or slips when walked on, Plug the Power CORD. Next, remove, Top