Hearth and Home Technologies 8000CF-OAK-IPI, 8000CFLP-OAKIPI 14 , 14

Heat & Glo • 8000CF-OAK-IPI • 2059-900 Rev. Q • 11/08 47

1

2

4

67

810

9

A. Remove Fixed Glass Assembly

See Section 14.I.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the

ﬁ rebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated

inside the ﬁ rebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included

with accessories. Contact your dealer for a list of ap-

proved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY

Hearth & Home Technologies-approved optional acces-

sories with this appliance. Using non-listed accessories

could result in a safety hazard and will void the warranty.

14

14 Appliance Setup

Figure 14.1

E. Removing Optional GFK-160A Fan

ITEM SEE FIGURE 14.1

1 Remove front from the ﬁ replace.

2 Remove glass assembly from the ﬁ replace.

3 Remove logs.

4 Remove grate.

5 Remove optional side and back refractory.

6 Remove base refractory.

7 Remove burner assembly.

8 Remove steel false base pan.

9 Remove valve assembly.

10 Disconnect fan and remove it through the valve

assembly cavity.

Figure 14.2

REMOVE FAN THROUGH

VALVE ASSEMBLY CAVITY 10

RHEOSTAT

Figure 14.3 Rheostat Location

Contents

Main Owners Manual NOTICE DO NOT DISCARD Models: 8000CF-OAK-IPI 8000CFLP-OAKIPI Listing Label Information/Location A. Congratulations Homeowner Reference Information Safety Alert Key: Table of Contents 1 Listing and Code Approvals User Guide 2 Operating Instructions 3 Maintenance and Service Page B. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY B. Limited Lifetime Warranty (continued) 1 B. Tempered Glass Speci cations C. BTU Speci cations A. Appliance Certi cation E. Non-Combustible Materials Speci cation 1 H. Requirements for the Commonwealth of Massachusetts 2 User Guide 2 B. Your Fireplace A. Gas Fireplace Safety D. Clear Space C. Fan Kit (optional) F. Fixed Glass Assembly E. Decorative Doors and Fronts G. Remote Controls, Wall Controls and Wall Switches CAUTION: NOT FOR USE WITH SOLID FUEL WARNING: DO NOT CONNECT 110 VAC TO THE CONTROL VALVE. J. After Fireplace is Lit K. Frequently Asked Questions 3 Glass Cleaning 3 A. Maintenance Tasks-Homeowner Doors, Surrounds, Fronts Remote Control Venting B. Maintenance Tasks-Quali ed Service Technician Gasket Seal and Glass Assembly Inspection Logs Firebox Page 4 A. Typical Appliance System Figure 4.1 Typical System Installer Guide B. Design and Installation Considerations D. Inspect Appliance and Components C. Tools and Supplies Needed 5 A. Selecting Appliance Location B. Constructing the Appliance Chase C. Clearances D. Mantel and Wall Projections 6 A. Vent Termination Minimum Clearances 6 V = VENT TERMINAL X Covered Alcove Applications 7 A. Approved Pipe C. Use of Elbows 7 B. Vent Table Key D. Measuring Standards H H One Elbow E. Vent Diagrams Two Elbows Top Vent - Horizontal Termination Heat & Glo 8000CF-OAK-IPI 2059-900 Rev. Q 11/08 25 Top Vent - Horizontal Termination - (continued) Three Elbows H V H V Top Vent - Vertical Termination No Elbow V1 = 50 ft. Max. (15.2 m) V1 = 3 ft. Min. (914 mm) Installing the ue restrictor BREAK HERE Two Elbows Three Elbows Top Vent - Vertical Termination - (continued) 8 A. Pipe Clearances to Combustibles 8 B. Wall Penetration Framing C. Install the Ceiling Firestop D. Install Attic Insulation Shield 9 A. Attaching Sheetrock Ledges B. Temporary Access Panel C. Securing and Leveling the Appliance D. Installing the Fiberglass Gasket F. Checking Pilot Plate E. Completing Grate Set-up 10 10 A. Assemble Vent Sections A B B. Assemble Slip Sections C. Secure the Vent Sections Page E. Install Metal Roof Flashing F. Assemble and Install Storm Collar G. Install RF4-8 H. Install Vertical Termination Cap I. Heat Shield Requirements for Horizontal Termination J. Install Horizontal Termination Cap 11 A. Fuel Conversion B. Gas Pressure C. Gas Connection 11 12 12 D. Electrical Service and Repair ORG GRN Figure 12.1 Intelli re Pilot Ignition (IPI) Wiring Diagram BRN BRN F. Wall Switch Installation for Fan (Optional) E. Junction Box Installation 13 13 A. Mantel and Wall Projections B. Facing Material 14 A. Remove Fixed Glass Assembly B. Remove the Shipping Materials C. Clean the Appliance D. Accessories G. Ember Placement F. Install the Optional Refractory Page Page M. Air Shutter Setting I. Fixed Glass Assembly Removing Fixed Glass Assembly Replacing Fixed Glass Assembly J. Install the Mesh 15 15 A. Intelli re Ignition System Symptom Possible Cause Corrective Action Intelli re Ignition System - (continued) Symptom Possible Cause Corrective Action 16 16 A. Appliance Dimension Diagram Heat & Glo 8000CF-OAK-IPI 2059-900 Rev. Q 11/08 55 B. Vent Components Diagrams Figure 16.2 DVP vent components DVP-TRAP1 DVP-TRAP2 DVP-TRAPK2 DVP-TRAPK1 Page Page Page C. Service Parts List 8000CF-OAK-IPI at Depot Intermittent Pilot Ignition Valve Assembly Service Parts 8000CF-OAK-IPI at Depot NOTICE