GFK-160A Blower System

- Installation and Operating Instructions -

1.0 INTRODUCTION

The GFK-160A Blower has been designed to circulate room air through the fireplace to enhance heat output. The GFK160A blower system operates on 120 VAC, 60 Hz power. This is available through a receptacle in the factory installed junc- tion box. The junction box is located in the controls com- partment of the fireplace.

A variable speed control is provided with the blower system to provide quiet forced air flow at the desired speeds. A tem- perature sensor switch, which automatically turns the blower ON/OFF, is also provided with this kit.

2.0 CHECK CONTENTS OF SHIPPING CARTON

Compare CONTENTS OF CARTON in Figure 1 with the ac- tual parts received. If any parts are missing or damaged, contact your dealer before starting installation. Do not in- stall a damaged blower kit.

WARNING: DO NOT CONNECT 110-120 VAC WIRING TO THE GAS CONTROL VALVE OF THIS FIREPLACE.

4.0INSTALLATION INSTRUCTIONS

4.1INSTALLING ELECTRICAL SERVICE TO THE JUNCTION BOX

WARNING: TURN ELECTRICAL POWER OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING THIS INSTAL- LATION.

1.Remove the electrical cover plate from the lower exterior of the fireplace. Remove the knock-out from the plate and attach the Romex clamp (screws to the outside). (See Figure 2). NOTE: Some fireplace models have a round hole through which the service wires are fed and into which the Romex clamp is attached. These models do not have a cover plate.

BLOWER

CONTROL

KNOB

GROUND

WING

NUT

CLIP

 

 

TEMP.

CONTROL

SENSOR

SWITCH

NUT

 

SPEED

LOWER

GRILLE

CONTROL

FIGURE 1

FIGURE 2

110-120 VAC

COVER

PLATE

3.0 INSTALLATION PRECAUTIONS

The GFK-160A Blower Kit is tested and safe when installed in accordance with this installation manual. It is your respon- sibility to read all instructions before starting installation and to follow these instructions carefully during installation to as- sure maximum benefit from, and safe operation of, the blower.

This blower is carefully engineered and must be installed only as specified. If you modify it or any of its components, you may cause a fire hazard and will void the WARRANTY. In addition, such action may void the coverage provided by the owner's home insurance.

CAUTION: All wiring should be done by a qualified electri- cian and shall be in compliance with local codes and with the National Electric Code ANSI/NFPA NO. 70-current (in the United States), or with the current CSA C22.1 Canadian Electric Code (in Canada).

2.Feed the 110-120 VAC electrical service wires through the Romex clamp and secure the wires to the clamp. Reattach the cover plate to the outside of the fireplace.

3.Access the controls compartment of the fireplace to lo- cate the Junction Box.

4.Using the wire nuts, attach the black wire to the black ser- vice wire, the white wire to the white service wire, and the service ground wire to the ground stud of the junction box.

5.Attach the junction box to the side of the unit. Insert the rear tab of the box into the rectangular slot in the outer wrap of the firebox. Push the front end of the box tightly against the side of the unit, and secure the box with a sheet metal screw (note the hole in the front end tab).

Printed in U.S.A. Copyright 2003

 

Hearth & Home Technologies Inc., 20802 Kensington Blvd., Lakeville, MN 55044

107-981K 5/03

1

Page 1 Page 2
Page 1
Image 1
Hearth and Home Technologies GFK-160A installation instructions Introduction, Check Contents of Shipping Carton
Page 1 Page 2

GFK-160A specifications

Hearth and Home Technologies has established itself as a leader in the fireplace and heating industry, and the GFK-160A blower is a prime example of their dedication to quality and innovation. This versatile and powerful blower enhances the efficiency of gas fireplaces, providing not only comfort but also improved heat distribution throughout your living space.

One of the primary features of the GFK-160A is its high-performance design, which allows it to generate a significant airflow of 160 CFM (Cubic Feet per Minute). This impressive output ensures that warm air from the fireplace is circulated efficiently, enabling you to enjoy the full benefits of your heating system. With this blower, the heat generated by your gas fireplace is distributed evenly, eliminating cold spots and creating a cozy atmosphere in your home.

The installation of the GFK-160A is straightforward, making it accessible for both professionals and DIY enthusiasts. Designed to fit a variety of gas fireplace models, this blower can be easily integrated into existing setups, enhancing their performance without requiring extensive modifications. The compact design also ensures that the blower will not take up unnecessary space, allowing for a seamless integration into your fireplace system.

Another notable characteristic of the GFK-160A is its reliable operation. The blower comes equipped with a built-in temperature sensor, which automatically activates the fan when the fireplace reaches a specified temperature. This smart technology not only enhances efficiency but also ensures that the blower runs only when needed, reducing energy consumption and associated costs.

Noise levels are always a concern when it comes to blowers, but the GFK-160A operates quietly, ensuring that you can enjoy the ambiance of your fireplace without disturbance. The low-noise operation allows it to blend into your home environment seamlessly, providing comfort without compromising tranquility.

In conclusion, the Hearth and Home Technologies GFK-160A blower stands out for its impressive airflow capacity, ease of installation, smart operational features, and quiet performance. By choosing the GFK-160A, homeowners can significantly improve the efficiency of their gas fireplaces, turning them into effective heating solutions that offer warmth and comfort during the colder months. With its robust features and reputable brand legacy, this blower is a valuable addition to any gas fireplace system.
Top Page Image Contents