HRV200PLUS INSTALLATION INSTRUCTIONS

M. MAINTENANCE INSTRUCTIONS

Proper maintenance is critical to the proper operation of the HRV200PLUS. The following schedule should be followed:

1.Monthly Maintenance - Inspect Exterior Hoods

Make sure exhaust and fresh air supply hoods are not blocked or restricted by leaves, grass, or snow. In winter, it is especially important to make sure snow is not blocking the hoods or that frost has not built up on the wire mesh (bird screen).

WARNING!

Blockage of weather hoods may cause a pressure imbalance within the house. Severe blockage will cause intermittent operation of the Fresh Air Fireplace!

2.Quarterly Maintenance

a.Clean Air Filters

The standard filters equipped with your HRV200PLUS are removable and washable.

1)Open the access door.

2)Carefully grip the end of the core and pull evenly outward until the core slides out one or two inches.

3)Remove the filter clips.

4)Once clips are removed, filters can be taken off the core and rinsed with water or a combination of mild soap and water. Do not clean in the dishwasher.

5)To reassemble, place the clean filters (wet or dry) back into their positions against the core and return the clips to their original position.

6)Slide the core back into its original position.

b.Check and Clean Drain Lines

3.Semi Annual Maintenance - Clean Core

a.Open the access door.

b.Carefully grip the ends of the core and pull evenly outward until core slides out. Core may be snug, but will slide out of the channel.

c.Remove the filter clips and filters. Rinse filters with warm soapy water.

d.Wash the core in warm soapy water (do not use the dishwasher).

Note: Core installation label is on the outer end of the core.

e.Install the clean core as follows:

1)Locate the filters on the core to cover the open surface and replace the filter clips.

2)Mount the bottom flange of the core guide into the H channel approximately 1/4” (6mm).

3)Mount the left or right flange of the core guide into the H channel approximately 1/4” (6mm) followed by the other side.

4)Mount the top flange of the core guide into the H channel approximately 1/4” (6mm).

5)With all four corners in place and the core straight and even, push firmly in the center of the core until the core stops on the back of the cabinet.

Note: Core will appear to stick out from the cabinet approximately 1/8” (3mm). This is designed this way so the access door will fit tight against the core.

02/04

4034-102 Rev F

39

Page 38 Page 40
Page 39
Image 39
Hearth and Home Technologies HRV200PLUS manual Maintenance Instructions, Monthly Maintenance Inspect Exterior Hoods
Page 38 Page 40

HRV200PLUS specifications

The Hearth and Home Technologies HRV200PLUS is an advanced heat recovery ventilator (HRV) designed to provide optimal indoor air quality while ensuring energy efficiency. As homes become increasingly airtight due to modern construction techniques, the importance of proper ventilation grows. The HRV200PLUS addresses this need by continuously exchanging stale indoor air with fresh outdoor air, effectively maintaining a healthy living environment.

One of the standout features of the HRV200PLUS is its innovative heat recovery technology. This system captures the heat from the outgoing air and transfers it to the incoming fresh air. As a result, the air being brought into the home is pre-warmed, reducing the demand on heating systems during the colder months. This energy-efficient method helps homeowners save on heating costs while maintaining comfort levels inside the home.

Another notable characteristic of the HRV200PLUS is its quiet operation. Equipped with high-performance, low-noise fans, this unit operates in silence, ensuring that occupants can enjoy a peaceful environment without the disruptive sounds often associated with ventilation systems. Additionally, the HRV200PLUS provides versatile installation options, allowing it to be easily integrated into both new and existing homes.

The unit features adjustable settings that allow users to customize airflow according to their specific needs. With multiple fan speeds, homeowners can choose the most suitable option for their daily activities, ensuring an ideal balance between indoor air quality and energy use. Furthermore, the HRV200PLUS includes a built-in filter system that captures dust, allergens, and other airborne particles, enhancing overall air quality.

Durability and ease of maintenance are also keys in the design of the HRV200PLUS. Constructed with high-quality materials, this unit is made to last, reducing the need for frequent replacements. The filters are easily accessible, making periodic maintenance straightforward, which further extends the product's lifespan.

In summary, the Hearth and Home Technologies HRV200PLUS stands out as a premium choice for homeowners seeking a reliable and efficient ventilation solution. Its combination of heat recovery technology, quiet operation, customizable settings, and easy maintenance make it an ideal option for improving indoor air quality while keeping energy costs in check. As the emphasis on healthy living spaces continues to grow, the HRV200PLUS remains a practical investment for modern homes.
Top Page Image Contents