B. As an Insert

• A retaining method may be needed to secure the heater

Pre-installation Preparation

 

in place.

• Combustible facing material may be installed over the

This insert and its components are tested and safe when in-

original combustible or noncombustible facing material on

stalled in accordance with this manual. Report to your dealer

the solid fuel fireplace. The original specified clearances

any parts damaged in shipment, particularly the condition

of a factory-built fireplace must be maintained, with

of the glass. Do not install any heater with damaged, in-

the exception of the hearth. Clearances on a masonry

complete or substitute parts.

fireplace must be maintained at 12 in. from the opening

 

 

for combustible projections over 1-1/2 in. Clearances for

 

WARNING

combustible projections under 1-1/2 in. must be maintained

per NFPA 211. Plan the surround size accordingly. A front

 

Fire Risk

face must be used with the insert.

• The insert front face is tested and approved with this insert

 

and may cover existing air circulation vents or grilles on the

 

solid fuel fireplace it is installed into. Should the face not

• Do not install or operate damaged heater.

cover the entire ventilation grille surface, the grille should

• Do not modify heater.

be left open.

• Installation other than as instructed by Hearth & Home

• The solid fuel fireplace’s flue damper must be fully locked

Technologies Inc. is strictly prohibited.

in the closed position or removed for installation.

• Do not operate the heater without fully assembling all

 

 

 

components.

 

Note: Decorative trim front faces have been

 

• Installation and/or use of any component part not

 

tested and approved to cover existing air

 

approved by Hearth & Home Technologies.

 

circulation vents or grills.

 

Hearth & Home Technologies disclaims any responsibility

 

 

 

• The chimney must be capped.

for, and the warranty and agency listing will be voided by

the above actions.

• Install the insert without the front face and make all

 

electrical connections.

 

Installation

•These inserts are designed for installations into solid fuel masonry or factory built noncombustible fireplaces that have been installed in accordance with the national, provincial, state or local building codes.

•You should seal off the area between the termination cap and the top of the existing chimney opening to avoid down drafts, moisture and/or cold air problems.

•Minimum fireplace opening requirements are shown in Figures 3.1 and 3.2 of this installation manual. The firebrick (refractory) can be removed from a factory built fireplace in order to gain minimum insert opening requirements.

•This insert requires no hearth extensions. Combustible material on the floor may be installed up to the insert. Do not obstruct the lower grill of the insert. The original fireplace cannot be returned to solid fuel in this condition.

•The metal floor of the solid fuel firebox may be removed to facilitate the installation of the insert. The side walls and top structure of the firebox may not be altered with the exception of removable baffles and dampers. The original fireplace cannot be returned to solid fuel in this condition.

•Position, Level and Secure Insert

•Place the heater into position.

•Level the heater from side to side and from front to back. If necessary, use the leveling bolts included in the manual bag. Screw the bolts into the nuts installed in the bottom of the insert (see replacement parts diagram). Turn bolts in until the insert is level.

Note: The warning label above, located in the instruction package, must be affixed to the lower back wall of the existing fireplace prior to installation of the insert.

Note: When the front is installed it will cover the gap between the heater and the framing, cabinet, finishing materials or existing fireplace.

10

Quadra-Fire • QV26E • 4038-827 Rev E • 02/05

Page 9 Page 11
Page 10
Image 10
Hearth and Home Technologies QV26E owner manual As an Insert, Glass. Do not install any heater with damaged
Page 9 Page 11

QV26E specifications

Hearth and Home Technologies has long been a leader in the fireplace and heating industry, and their QV26E model stands as a testament to their commitment to innovation and quality. The QV26E is a versatile, zero-clearance gas fireplace that seamlessly blends aesthetics with functionality, catering to both contemporary and traditional home designs.

One of the primary features of the QV26E is its large viewing area. The fireplace boasts a beautifully designed front that allows for an unobstructed view of the flames, creating a warm and inviting ambiance in any room. The large glass door not only enhances the visual appeal but also ensures maximum efficiency by providing better heat retention.

The QV26E is equipped with advanced technology that promotes efficiency and ease of use. Its electronic ignition system allows for reliable startups with the push of a button, eliminating the hassle of traditional match lighting. The model features adjustable flame height, enabling users to customize the intensity of the fire according to their preferences. This adaptability is complemented by a fan-forced heater, which circulates warm air throughout the space, enhancing heat distribution.

Energy efficiency is a hallmark of the QV26E. With an impressive annual fuel utilization efficiency (AFUE) rating, this gas fireplace conserves energy while delivering powerful heating performance. It can be configured for either natural gas or propane, providing flexibility based on the homeowner's needs.

The QV26E also includes easy-to-adjust controls, allowing users to manage the heat output and ambiance without any fuss. Additionally, it comes with a remote control option, enabling homeowners to ignite or extinguish the fire from the comfort of their seats.

Aesthetically, the QV26E offers a variety of styling options. Users can select from different media and log sets to create a personalized look that complements their interior decor. The fireplace is available in multiple finishes, ensuring that it fits harmoniously into any space.

Overall, Hearth and Home Technologies' QV26E model combines safety, efficiency, and beauty, making it a prime choice for those looking to enhance their living environment with a cozy and stylish heating solution. Whether you're looking to create a focal point in your home or simply seeking effective heating, the QV26E delivers in every aspect.
Top Page Image Contents