Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies RHW-485H owner manual 14-1/2

Models: RHW-485 RHW-485H

1 48

Download 48 pages 57.48 Kb

Page 39

		Inside
		Diameter
		8 in. (203 mm)
		Outside
	Effective	Diameter
	Effective	10-1/2 in.
	Height	10-1/2 in.
	Height	(267 mm)
	4-3/4 in.	(267 mm)
	4-3/4 in.
	(121 mm)

SL315/SL330 Offset/Return

14-1/2 in.

(368 mm)

24 in.

(610 mm)

AS8 Straight Attic Insulation Shield

10-1/2 in.

(267 mm)

2 in. (51 mm)

JB877 Chimney Joint Band

10-1/2 in. (267 mm)

CB876 Chimney Joint Band

A

B		14-1/2 in.
		(368 mm)
	Ceiling Firestop

Catalog #	A		B
FS338	0-deg.	14-1/2 in.		368 mm
FS339	15-deg.	18-3/8 in.		467 mm

FS340	30-deg.	23 in.		584 mm

12 in. (305 mm)

24-5/8 in.

(625 mm)

27-3/8 in.

(695 mm)

RF370 Roof Flashing

12 in. (305 mm)

24-5/8 in. (625 mm)

31 in. (787 mm)

RF371 Roof Flashing

Heat & Glo • RHW-485 • 33221 Rev O • 08/06

39

Image 39

Hearth and Home Technologies RHW-485H owner manual 14-1/2

Contents

Fire Risk Models RHW-485, RHW-485H Woodburning FireplaceListing Label Information/Location GrateNumber Table of Contents Listing and Code Approvals Appliance CertiﬁcationNot intended for use as a primary heat source Asphyxiation Risk Design and Installation ConsiderationsGetting Started Negative PressureMarginal Location Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Construct the ChaseRisk of Smoke Spillage Installation of FireplaceInstall the Outside Air Kit Sharp Edges Asphyxiation RiskFt min. from top of uppermost chimney section to air inlet Level the Fireplace Secure the FireplacePosition the Fireplace Place the Protective Metal Hearth StripsChimney Assembly Height of Chimney Components Degree SL306 SL312 SL318 SL324 SL336 SL348 Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Chimney Termination Complete the EnclosureInstall the Termination Cap Install the Chimney Air Kit required in CanadaChase Top Installing an ST375 Square Termination Cap Accessories Gas Log/Lighter ProvisionsGas Code, Ansi Z223.1 Hearth Extension FinishingCombustible Material Finishing MaterialMantel Glass DoorsGeneral Information Operating InstructionsFirescreen Outside AirClear Space Near the Fireplace Flue DamperMoisture GrateWood Fuel FirewoodStarting a Fire Understanding Vent Problems TroubleshootingCan’t get a good ﬁre going. What am I doing wrong? Diagnostics and Problem SolvingDiagnostic Questions Solutionsﬁreplace burns the wood too fast. What can I do? Firebox Refractory Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Disposal of AshesChimney Fire Maintenance Task ListWhen cleaning glass door CleanReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney Components14-1/2 1829 mm 10-7/8 276 mm 406 mm 508 mm 20 x Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XMinimum Base Dimensions 26.5 X 28 with 34 X 34 with TR442 TR442 / 444 TVThis page intentionally left blank RHW-485 Service PartsHerringbone Brick Refractory option available week 03/04 Description of Part RHW-485 RHW-485H QtyThis page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesDo Discardnot Contact Information