C. 240VAC Hardwire Installation

(Minimum 14 gauge three conductor wire, non-metallic sheathing with ground.)

Turn off circuit breaker.

Remove access knockout located on right side of heater.

Disconnect black and white wires between the heater and plug. Remove the power cord from the cover plate. Remove the electrical knockout and install the cable clamp (not provided) onto the cover plate. Remove the connectors on the wires from the heater and strip them back 1/2 in.

Feed 8 in. of service wire through cable clamp (not provided) and secure.

Connect black, white and red wires of the heater to the black, white and red wires from the service. Connect green (ground) wire from heater to the ground of the service. See Figure 4.1.

Wall switch wiring (see below) is to be done at this time.

Cover access hole with a 4 in. cover plate (not provided) if required.

Remove the protective cover by cutting the tape located on the outer perimeter.

D. Wall Switch Wiring (12VDC)

*Do not connect wires to 120/240VAC* (hardwired heat- ers only)

Turn off circuit breaker.

Remove access knockout located on right side of heater.

Feed 8 in. of wire for the wall switch through the cable clamp and secure. Low voltage wire can be used for the wall switch connection. It is recommended to only go 10 ft from the heater to the wall switch.

Locate the light blue (wall switch) wires in the heater. Connect one wall switch (blue) wire to wire for switch and connect the other wall switch (blue) wire to the other wire for switch.

Cover access hole with a 4 in. cover plate (not provided) if required.

Run the wall switch wire to the wall box and connect to a wall switch (WSK-21 & WSK-21-W).

LAMP LAMP

120VAC

LAMPS

DIMMER

B

A

GROUND

NEUTRAL

120VAC 60Hz

LINE1 HOT

120VAC 60Hz

240VAC 60Hz

 

LINE2 HOT

120VAC PLUG or 120/240VAC HARD WIRED

FLAME MOTOR

B

A

R2

SPEED CONTROL

-12VDC

OPTIONAL

 

 

 

 

 

D1

THERMOSTAT

REMOTE OR

REMOTE

RELAY

DIODE

WALL ON/OFF

HEAT

 

 

SWITCH

CONTROL

 

 

 

 

 

HEAT SWITCH

-+

12VDC

SUPPLY

POWER

WHITE

 

BLOWER

 

BLOWER

 

 

 

 

120VAC

 

-12VDC

BLACK

HIGH LIMIT HEATER1

HIGH LIMIT

HEATER1

 

 

 

BLACK

 

 

 

240VAC

 

RED

 

HEATER2

 

 

 

RED

3PIN WIRING HARNESS

120VAC - 240VAC 60HZ SPLIT-PHASE

POWER NEUTRAL MUST NOT CONNECT TO VIRTUAL NEUTRAL OF HEATERS OR BLOWER IN 240VAC VERSION

￿Figure 4.1 120V/240V Wiring Diagram

10

Heatilator • SILHOUETTE Series Electric Fireplace • 4030-155 Rev K • 04/05

Page 10
Image 10
Hearth and Home Technologies SILH50EV, SILH50ENH, SILH60ENH 240VAC Hardwire Installation, Wall Switch Wiring 12VDC

SILH50E, SILH60EV, SILH50ENH, SILH60ENH, SILH60E specifications

Hearth and Home Technologies offers a variety of innovative fireplace models, including the SILH50EV, SILH60E, SILH60ENH, SILH50ENH, and SILH60EV. These models are designed to meet various heating needs while providing aesthetic appeal and advanced technology.

The SILH50EV and SILH60E models are known for their sleek, modern designs and efficient heat output. Their large viewing areas provide a stunning view of the flames, enhancing the ambiance of any space. Both models use direct vent technology, which allows for efficient combustion while minimizing heat loss. This technology ensures that the fireplace draws air from outside for combustion, thus preserving indoor air quality and improving energy efficiency.

The SILH60ENH and SILH50ENH models are specifically designed with enhanced comfort and functionality in mind. These models feature advanced blower systems that distribute heat evenly throughout the home, making them ideal for larger spaces. The ENH models are equipped with smart technology, allowing users to control the fireplace remotely via a smartphone app, adding convenience to any living environment.

The SILH60EV model stands out for its versatility and customization options. Homeowners have the choice of various log sets, flame colors, and ember bed lighting to create a personalized aesthetic. This model also integrates seamlessly with home automation systems, providing an elegant solution for modern living.

All models are constructed with high-quality materials, ensuring durability and longevity. The glass doors are designed for optimal visibility and are made from crystal-clear, heat-resistant glass, allowing for a mesmerizing view of the flames without compromising safety.

Safety features across the series include automatic shut-off systems and tempered glass to protect against burns. These fireplaces also meet stringent environmental standards for emissions, aligning with the growing demand for eco-friendly home heating options.

In summary, the SILH series from Hearth and Home Technologies offers a combination of style, efficiency, and advanced technology. From modern aesthetics to smart features and robust heating capabilities, these models are designed to enhance the comfort and ambiance of any home. Whether for a cozy evening or large gatherings, the SILH50EV, SILH60E, SILH60ENH, SILH50ENH, and SILH60EV provide reliable warmth and visual appeal.