H. Control Module Operation

1.The control module has an ON/OFF/REMOTE selector switch that must be set. See Figure 2.3.

OFF Position: Appliance will ignore all power inputs and will not respond to any commands from a wall switch or remote. The unit should be in the OFF position during installation, service, battery installation, fuel conversion, and in the event that the control goes into LOCK-OUT mode as a result of an error code.

ON Position: Appliance will ignite and run continuously in the HI flame setting, with no adjustment in flame output. This mode of operation is primarily used for initial installation or power outage operation with battery backup.

REMOTE Position: Appliance will initiate commands from an optional wired wall switch and/or the wireless remote (RC300).

2.If using a wired wall switch with the module in REMOTE mode, the fl ame output can be adjusted with the HI/LO selector switch on the module. See Figure 2.3. Note that the flame HI/LO selector switch will become inactive once an optional remote control (RC200/RC300) is programmed to the control module. Note that the control module will always ignite the fireplace on HI and remain so for the initial 10 seconds of operation. If the HI/LO is switched to the LO position, the flame output will automatically drop to the lowest setting after the fl ame has been established for 10 sec. After this 10 second period, the fl ame can be adjusted from HI to LO with the switch.

3.The control module has safety feature that automatically shuts down the fi replace after 9 hours of continuous operation without receiving a command from the RC300 remote.

4.If you intend to use both an optional wired wall switch and the RC300 remote control to operate your fireplace, the wall switch will override any commands given by the remote.

5.Module Reset

This module may lock-out under certain conditions. When this occurs, the appliance will not ignite or respond to commands. The module will go into lock-out mode by emitting three audible beeps, then continuously displaying a RED/GREEN error code at its status indicator LED.

• Check battery tray. Remove batteries if installed. Batteries should only be installed for use during power outages. See Section G.

Locate the module selector switch. (See Figure 2.3).

Set the module selector switch to the OFF position.

Wait five (5) minutes to allow possible accumulated gas to clear.

Set the module selector switch to ON or REMOTE position.

 

SELECTOR

 

SWITCH

STATUS INDICATOR LED

FLAME HI/LO SWITCH

NG/LP SETTING

Figure 2.3 Control Module

Start the appliance.

WARNING! Risk of Explosion! DO NOT press the mod- ule reset switch more than one time within a five minute time period. Gas may accumulate in firebox. Call a quali- fied service technician.

I. Before Lighting Fireplace

Before operating this fi replace for the fi rst time, have a qualified technician:

Verify all shipping materials have been removed from inside and/or underneath the fi rebox.

Review proper placement of logs, ember material and/or other decorative materials.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire/Asphyxiation! DO NOT oper- ate fireplace with fixed glass assembly removed.

An Intellifi re Plus™ ignition system is standard with this appliance.

Heat & Glo • Cosmo-I30, Cosmo-I352239-900 Rev. H • 1/11

9

Page 9
Image 9
Heat & Glo LifeStyle Cosmo-130 owner manual Control Module Operation, Before Lighting Fireplace, Module Reset

Cosmo-130 specifications

The Heat & Glo LifeStyle Cosmo-130 is a modern gas fireplace that exemplifies innovation in heating design and functionality. This fireplace blends contemporary style with advanced technology, making it a perfect addition for any contemporary living space. Its sleek and minimalist design ensures that it not only serves as a heat source but also as a striking focal point in your home.

One of the main features of the Cosmo-130 is its impressive viewing area. The large glass front allows for an unobstructed view of the flames, creating an inviting ambiance. The design prioritizes aesthetics, with the fireplace being available in multiple configurations, including linear and traditional styles, enabling it to fit seamlessly into various interior designs.

With a focus on efficiency, the Cosmo-130 operates using an advanced gas burner system, which optimizes fuel use while producing substantial heat output. This fireplace boasts an impressive thermal efficiency rating, ensuring that heat is effectively distributed throughout the room while minimizing energy consumption.

The LifeStyle Cosmo-130 employs cutting-edge technology with its intuitive electronic controls. Homeowners can easily adjust the flame height and heat output to suit their preferences using a remote control or a smartphone app. This level of control contributes not only to comfort but also to energy efficiency, allowing users to personalize their heating experience.

Another notable aspect is the fireplace's customizable media options. Customers can choose from various decorative media, including logs, crystals, or stones, allowing for personalization to match different décor styles. This flexibility enhances the visual appeal of the fireplace and caters to individual tastes.

Safety is paramount in the design of the LifeStyle Cosmo-130. It includes features such as a thermostat that automatically maintains desired temperatures, as well as a safety shut-off system that activates should the unit overheat. This ensures peace of mind for users, especially in homes with children and pets.

With an emphasis on convenience and style, the Heat & Glo LifeStyle Cosmo-130 is an exceptional choice for those looking to enhance their home with a sophisticated heating solution. Its combination of aesthetic appeal, user-friendly technology, and efficient performance make it a standout option in the world of modern fireplaces, promising warmth and elegance in any setting.