10 Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric

Code CSA C22.1.

This appliance comes standard with a 120 VAC cord assembly which has a female plug in to accommodate all control options and accessories. See Figure 10.1. This is required for proper operation of the appliance (IntelliFire Ignition). An outlet box may be installed in a bottom back corner of the existing solid fuel masonry or factory built fireplace to plug in the cord assembly, or the supplied power cord may be routed out onto the hearth to a nearby outlet.

A 120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Low voltage and 120 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 120V to the valve or to the appliance wall switch. Incor- rect wiring will damage controls.

An IntelliFire Plus™ ignition system is standard with this appliance.

B. IntelliFire Plus™ Ignition System Wiring

Wire an outlet box (120VAC) in the bottom back corner of the existing solid fuel masonry or factory built fireplace to plug in the cord assembly. The supplied cord assembly may also be routed out onto the hearth to a nearby outlet.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

Refer to Figure 10.1, IPI Wiring Diagram.

This appliance is equipped with an IntelliFire Plus™ control valve which operates on a 6 volt/1.5 AMP system.

Plug the 6 volt transformer plug into the cord assembly to supply power to the insert OR install 4 AA cell batteries (not included) into the battery pack before use.

ON/OFF Switch

An ON/OFF switch is included with the appliance surround and should be attached to surround/facing. (See Installation instructions for remote control/fronts).

If desired an additional wall switch or thermostat may be added to system as shown in Figure 10.1.

 

 

INTERMITTENT

 

 

 

 

 

 

PILOT IGNITOR

 

 

 

 

 

 

 

 

RC100

RC200

RC300

TO CORD ASSEMBLY

 

 

 

(OPTIONAL WALL CONTROLS)

120VAC

 

MODULE

 

 

 

 

 

 

 

 

 

AUX2 NOT USED FOR INSERT MODELS.

 

 

ORG

 

AUX300 MODULE

 

 

 

 

 

PROTECTIVE COVER INCLUDED

 

 

WHT

 

 

 

FLAME

 

FAN

 

TO CORD

 

 

 

AUX1 AUX2

 

MODULATION

 

 

 

 

 

 

ASSEMBLY

 

 

 

 

 

 

 

 

 

 

 

 

(110V)

 

 

 

 

BATTERY PACK

 

 

 

 

RED

6V DC

 

 

ORANGE

GREEN

RED

BLK

 

 

ROCKER

(PILOT)

(MAIN)

BLK

 

 

 

SWITCH

 

 

BROWN

 

 

 

 

 

 

 

WALL SWITCH

 

 

 

 

 

OR REMOTE

 

 

 

 

GROUND

INSTALL

 

 

Figure 10.1 IPI Wiring Diagram

Heat & Glo • Cosmo-I30, Cosmo-I352239-900 Rev. H • 1/11

25

Page 25
Image 25
Heat & Glo LifeStyle COSMO-I30 Electrical Information, Wiring Requirements, IntelliFire Plus Ignition System Wiring

COSMO-I35, COSMO-I30 specifications

The Heat & Glo LifeStyle COSMO-I30 and COSMO-I35 fireplaces are revolutionary additions to modern living spaces, merging outstanding design with advanced technology. Both models are designed to enhance your home's aesthetics while providing efficient heating solutions.

The COSMO-I30 is a 30-inch linear fireplace, while the COSMO-I35 is the larger 35-inch version, allowing homeowners to choose the perfect size to complement their space. These zero-clearance fireplaces can be easily installed in various locations, including existing masonry or prefabricated fireplaces, or even as stand-alone features. This versatility makes them suitable for both remodeling projects and new constructions.

One of the standout features of both models is the innovative design that emphasizes a contemporary look. The clean, linear flame provides a warm ambiance without the clutter of traditional fireplaces. You can enjoy the dancing flames through a sleek front glass panel that maintains a clear view of the fire while enhancing safety.

The COSMO series incorporates advanced technology to ensure optimal performance and energy efficiency. Both models utilize proprietary technology that allows for reliable operation and minimal emissions. The Intellifire ignition system further enhances convenience, providing instant lighting with the push of a button. Homeowners can easily control the flames and heat output, adjusting the ambiance to suit their preferences.

Customizability is another appealing aspect of the COSMO series. The fireplaces come with a range of decorative options, including different styles of media such as glass, stones, or logs, allowing you to tailor the appearance to match your interior design. The ambient lighting feature adds another layer of sophistication, providing a soft glow that can be enjoyed even when the fire isn’t lit.

Both the COSMO-I30 and COSMO-I35 are energy-efficient, boasting high-efficiency ratings that help reduce heating costs without sacrificing comfort. They are designed to function efficiently, effectively distributing heat throughout the room.

With their striking design, innovative technology, and customizable options, the Heat & Glo LifeStyle COSMO-I30 and COSMO-I35 fireplaces create the perfect focal point in any living space, combining functionality with elegance for an unparalleled home experience.