50336/50337.instructions 3/26/01 11:29 AM Page 1
3-Way Motion
Sensing Switch
INSTALLING THE SWITCH
WARNING: Turn power off at the circuit breaker before wiring.
Note: a |
rate switches. If you want to use this product in a sin- |
gle switch circuit or if you want to install more than one |
•Remove remaining
•Add the jumper wire to the common lug and to either one of the two switched lugs. If you're not sure which lug is common, install the jumper on any two of the three wires, and test the jumper as explained on the next page.
Test for correct common wire connection:
Turn the circuit breaker back on.
The
The MSS can be used to replace either a
OFF AUTO ON
Features include:
•1500 motion detection angle
•Adjustable
•Adjustable photocell
•Works with incandescent and rapid start fluorescent lighting
•Works with motors up to 1/8 hp.
•Slide switch selectable OFF, ON AND AUTO modes.
Included are: • The sensor switch • Cover plate • 4 wire connectors • 2 large screws • 2 small screws.
motion sensing wall switch, see page 6 |
|
|
• Remove the decorative coverplate (secured by two |
|
|
screws). |
|
|
• Remove Control Cover. (Press in with screwdriver. |
|
|
Swing out cover to remove.) |
| ON |
• Choose which switch will be replaced and remove it. | OFF | AUTO |
| ||
|
| |
• For easier |
|
|
tape indicating where the wire had been connected. |
|
|
Hot Wire |
| Common Switch Lug |
The switch may
indicate the
commonCOMMON
OR
Color of screw
may be different for the common
Common
Switch Lug
Hot Wire
Jumper
To Brown wire
Leaving the jumpered switch in one position,
flip the other
Lights | Yes | Jumper is | ||||
turn on | correct. Go | |||||
|
| |||||
and off. |
|
| to next page. | |||
No |
|
|
|
|
| |
|
|
|
|
| ||
|
|
|
|
| ||
|
|
|
|
|
|
INSTALLATION
WARNING: For indoor use only.
SELECT A LOCATION
NEW APPLICATIONChoose a location where the motion sensor has a clear view of the entire area where occupant motion may occur.
RETROFIT APPLICATIONMotion sensing switch will replace existing wall switch. Use only where the existing switch location provides a clear view of the occupied area.
30' |
15' |
0' |
Typical Plan View of Coverage
Hot Wire |
To Red wire
of MSS
(note color)
of MSS
(note Color)
Move one end of the jumper |
|
|
|
|
| Flip the switch with the | ||||||||||
| wire to the previously |
|
|
|
|
| jumper wire to the | |||||||||
| unconnected terminal. |
|
|
|
|
| other position. | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Flip the unjumpered switch |
| |||||
| Remove the jumpered |
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
| on and off. |
| |||||||
|
| switch from the |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| junction box. |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Turn the power | No | Lights |
| Yes |
|
| Jumper is |
The detector is more sensitive to motion across the front of the sensor than to motion towards the sensor.
The detector senses heat in motion and possible heat sources that change temperature quickly. Therefore, to avoid false triggering, avoid placing the sensor where it will be aimed at air conditioners, heaters, and other sources of heat or cold.
• Connect the
Questions? Call
- 2 -
Single Switch Installation
- 3 -
ADJUSTMENTS
off at the |
| turn on |
| correct. Go |
|
| |||
circuit breaker. |
| and off. |
| to next page. |
- 4 -
TROUBLESHOOTING
≠Replace switch with MSS
• For single switch installations, connect the wall switch as shown
HOT
TIME | LIGHT LEVEL |
If you have a problem with your Wall Switch, first follow this guide. If the problem persists, call the customer service hotline at
Hot Wire
¨
Add
Jumper
Wire
Brown
Jumpered Wire
Black
Hot Wire
here.LOAD
OFF AUTO ON
BLACK Green ground wire to |
There are 6 preset selections for the | The sensor can be prevented from turning on lights | |
amount of time the lights stay on: Test (5 | ||
when there is already enough light in the room. Use a | ||
seconds), 1, 5, 10, 15, and 20 minutes. Use | ||
small phillips screw driver to set the light level using this | ||
a small, phillips screw driver to adjust the | ||
diagram as a guide. In the fully clock- | ||
TIME control (see Figure 4). Turn the TIME | ||
wise position, the sensor turns on | ||
control until it “snaps” into the desired time | ||
lights even in full daylight. In the fully | ||
position. | ||
| ||
| sor only turns on lights when the sur- | |
| rounding light level is very low. |
SYMPTOM | POSSIBLE CAUSE | |
|
|
|
|
|
|
Light does not come | 1. | Circuit breaker or fuse is |
on in the AUTO |
| turned off. |
mode. | 2. | If the lamp being controlled |
|
| has another switch, it may |
|
| be turned off. |
| 3. | Bulb is defective. |
| 4. | LIGHT control is set too far |
SYMPTOM | POSSIBLE CAUSE | |
|
|
|
|
|
|
Light does not turn | 1. | Incorrect wiring. |
off. | 2. | MODE switch is set to |
|
| ON instead of AUTO. |
| 3. | Motion is still present. |
| 4. | Delay set by TIME |
|
| control has not |
|
| expired. |
OFF AUTO ON
Green ground wire to
Red junction box screw or grounding wire
3-Way Motion Sensor Wiring Diagram
• Mount the MSS into the junction box with the two junction box screws. |
• Turn the circuit breaker back on. |
• Preset the controls: Time to min. (fully CCW), Photo Adjustment fully clockwise. Cover the lens with masking |
tape. |
• With the motion sensor in the "ON" position, turn the remote switch on and off several times. Go to step 1, 2, |
or 3, depending on results. |
junction box screw or |
grounding wire |
Red & Brown
3-Way with Two Motion Sensors
If you want to have motion sensors at both
Common Switch Lug
HOT
HOT
Any Light Level |
| Dark (low light level) |
|
| |
|
|
| To adjust the photocell: | ||
|
|
|
|
| |
|
|
| + | • When the light in the room is at the | |
| 5 | 10 |
| ||
|
|
|
|
| level you want the lights to turn on, |
| 1 |
| 15 |
| set the switch to the AUTO position. |
|
|
|
| • Put the TIME control to the 5 sec- | |
| Test | 20 |
|
| ond position. |
| T I M E | L I G H T |
| ||
| • Put the LIGHT control to the mini- | ||||
|
|
|
| ||
5 Seconds |
| 20 Minutes |
| mum dark (fully | |
|
| position. | |||
|
|
|
| • | Wait for the lights to turn off. |
|
|
|
|
| Turn the LIGHT adjustment clock- |
|
|
|
|
| wise in very small steps and wait 2 |
|
|
|
|
| seconds before moving your hand |
| toward the DARK position. |
5. | MODE switch is set to OFF |
| instead of AUTO. |
6. | Poor connection. |
|
|
1. | Motion has stopped in the |
Lights do not stay | room. |
on in the Auto mode. 2. | TIME control is set for too |
| short a delay. |
SPECIFICATIONS
Light comes on for | 1. | Heating or cooling ob- |
no reason in the Auto |
| jects (such as air |
mode. |
| vents, appliances, or |
|
| drafts through the wall |
|
| box) are causing false |
|
| triggering. |
| 2. | Switch on the sensor |
|
| has been turned off |
|
| and back on. |
| 3. | There was a momen- |
|
| tary power interrup- |
|
| tion. The light will turn |
|
| off automatically when |
|
| the "on" time expires. |
WARNING: Shut off all power at fuse box or circuit breaker before beginning installation.
in front of the sensor. Repeat until the lights controlled by the sensor come on. The light will now come on when the light level is at or below
Electrical input | 120V, 60 Hz |
Fluorescent Load | (2) 30 Watt minimum 400 Watt maximum Rapid Start |
Motor Load | 1/8 HP maximum |
Incandescent | 500W at 120V AC |
1.
If light does not turn on:
Exchange |
| ||
Red & Black |
|
| Test again. |
wires on |
|
| Go to 2 or 3. |
MSS Control |
|
|
|
| |||
|
|
|
| ||
Switch |
| Switch | |
|
|
|
|
|
|
| |
|
| Existing Wiring Diagram |
|
|
|
|
|
the present level and motion is detected.
Complete Installation
• Replace control panel cover and install the decorative wall plate. In installations where the GE motion sensor |
Adjustable approximately 5 sec. to 20 min. | |
Photocell Sensor | From dull daylight to less than 1 FC. |
Coverage | up to 15 ft. at 1500, up to 30 ft. in front of the sensor |
2.
3.
If light turns
on in only one
position of
remote switch:
If light turns
on with
remote switch
in either position:
| Exchange |
|
|
| |
| Red & Brown |
|
|
| Test again. |
| wires on |
|
|
| Go to 1 or 3. |
| MSS Control |
|
|
|
|
|
|
|
|
|
Set sensor to "AUTO". Wait for the unit to warm up (up to 1 min.). If the remote switch can turn the lights on, it's OK. Otherwise:
Exchange Red & Brown wires on MSS Control. Remove the
HOT
Red &
Brown
OFF AUTO ON
| Red & Brown |
Black | HOT |
OFF AUTO ON | |
| Black |
| Green ground wire to |
| junction box screw or |
| grounding wire |
switch is combined with other switches or outlets on an expanded box, a combination wall plate will need to |
be purchased. Various combination wall plates are available at Home Centers and Electrical Supply Stores. |
• Slide the switch a couple of times to make sure it operates freely. |
USE
MODE Selection Switch
Moving the switch selects one of three modes of operation: OFF, AUTO, ON
OFF: Lights stay off.
AUTO: Lights come on for time set when motion is detected and the light level is below the set level or when
WARNING
Risk of electric shock•Shut off power at fuse box or circuit breaker before installation
•Use indoors onlyRisk of fire• Do not exceed electrical ratingstape. Go to the next page.
Dual 3-Way Motion Sensor Wiring Diagram
ON: Lights stay on continuously. Flipping
Res. #8143555
- 5 - | - 6 - | - 7 - | - 8 - |