USING THE REMOTE TO CONTROL VCR FUNCTIONS

Operating the precoded function for your VCR.

This remote is designed to operate different types of VCRs. You must first program the remote to match the remote command set of your VCR (refer to page 41 for pre-codes).

1.Turn ON your VCR.

2.Aim the remote control at the front of your VCR.

3.Press and release the VCR button to switch to VCR pre-coded mode.

4.Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 41. The VCR button light will flash 3 times if the code was accepted.

5.Aim the remote at the VCR and press the POWER button. The remote will turn off your VCR if the correct two digit preset code is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off, try a different two digit preset code.

6.The remote will now control your VCR.

NOTES:

1.If your VCR cannot be operated after performing the above procedures, your VCR’s code has not been precoded into the remote.

2.In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.The MENU button will act as the VCR MENU button for HITACHI VCRs.

5.The LAST CH button will act as your VCR ENTER button if required.

6.The SLEEP button will act as your VCR ‘100’ button if required.

VCR Button

This button allows the remote to control your VCR by set- ting it to VCR mode.

PRECODED VCR Buttons

These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

 

 

POWER

 

 

 

 

 

 

 

TV

VCR

 

 

CBL

 

 

STB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SOURCE WIZARD

 

 

 

 

DVD

CD

 

 

PVR

 

 

AMP

 

 

 

 

 

 

 

 

1

 

 

2

 

 

 

3

 

 

 

4

 

 

5

 

 

 

6

 

 

 

7

 

 

8

 

 

 

9

 

 

SLEEP

 

 

0

 

 

 

 

INFO

ANT

TV/RGB

A/V NET

 

ASPECT

VIDEO

 

 

 

 

 

 

 

 

 

 

MENU

 

EXIT

 

 

 

 

 

VOL

 

SELECT

 

 

 

CH

 

 

 

 

 

 

 

 

 

 

 

 

 

MUTE

LAST

CH

 

 

 

 

 

 

 

 

 

 

 

 

 

VID1

 

 

 

 

 

 

 

VID

5

 

 

 

 

 

 

 

 

 

VID 2

 

VID 3

 

 

VID

4

 

 

 

 

 

 

 

 

 

 

 

 

 

PIP

 

 

SURF

 

 

 

FREEZE

 

 

 

 

 

PIP ACCESS

 

 

 

PIP MODE

 

 

SWAP

 

 

DAY/NIGHT

REC

MY VCR CODE IS:

THE REMOTE CONTROL

NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR.

35

Page 35
Image 35
Hitachi 32HDT55, 42HDT55, 50HDT55 Using the Remote to Control VCR Functions, Operating the precoded function for your VCR