Troubleshooting
Troubleshooting
PROBLEM | CAUSE | SOLUTION |
|
|
|
|
|
|
Gas engine pulls hard (won't start) | Hydraulic pressure is too high | Turn hydraulic pressure knob counter clock- |
|
| wise to lowest setting. |
|
|
|
Gas engine does not start | Switch OFF, low oil, no gasoline | Consult engine manual, supplied. |
Gas engine doesn't work properly | Faulty engine | Consult engine manual, supplied. |
| Elevation | Refer to Engine Repair Kit. |
|
| 4.0 hp - 288678 / 5.5 hp - 248943 / |
|
| 6/5 hp - 248944 / 9.0 hp - 248945 |
|
|
|
Gas engine operates, but displacement | Hydraulic pump valve is OFF | Set hydraulic pump valve ON. |
pump doesn't operate |
|
|
Pressure setting too low | Increase pressure. | |
| Displacement pump outlet filter (if used) | Clean the filter. |
| is dirty or clogged |
|
|
|
|
| Tip or tip filter (if used) is clogged | Remove tip and/or filter and clean. |
| Hydraulic fluid too low | Shut off sprayer. Add fluid*. |
| Belt worn or broken or off | Replace, page 12. |
| Hydraulic pump worn or damaged | Bring sprayer to Graco distributor for repair. |
| Dried paint seized paint pump rod | Service pump. See manual 311845. |
| Hydraulic motor not shifting | Set pump valve OFF. Turn pressure down. |
|
| Turn engine OFF. Pry rod up or down until |
|
| hydraulic motor shifts . |
|
|
|
Displacement pump operates, but output | Piston ball check not seating properly | Service piston ball check. See manual |
is low on upstroke |
| 311845. |
|
|
|
| Piston packings worn or damaged | Replace packings. See manual 311845. |
Displacement pump operates but output | Piston packings worn or damaged | Tighten packing nut or replace packings. |
is low on downstroke and/or on both |
| See manual 311845. |
strokes |
|
|
Intake valve ball check not seating | Service intake valve ball check. See man- | |
| properly | ual 311845. |
|
|
|
| Suction tube air leak |
|
Paint leaks and runs over side of wetcup | Loosen | Tighten |
| Throat packings worn or damaged | Replace packings. See manual 311845. |
Excessive leakage around hydraulic | Piston rod seal worn or damaged | Replace these parts. |
motor piston rod wiper |
|
|
|
|
|
Fluid delivery is low | Pressure setting too low | Increase pressure. |
| Displacement pump outlet filter (if used) | Clean filter. |
| is dirty or clogged |
|
|
|
|
| Intake line to pump inlet is not tight | Tighten. |
| Hydraulic motor is worn or damaged | Bring sprayer to Graco distributor for repair. |
| Large pressure drop in fluid hose | Use larger diameter or shorter hose. |
The sprayer overheats | Paint buildup on hydraulic components | Clean. |
Spitting from gun | Air in fluid pump or hose | Check for loose connections on siphon |
|
| assembly, tighten, then reprime pump. |
|
|
|
| Loose intake suction | Tighten. |
| Fluid supply is low or empty | Refill supply container. |
Excessive hydraulic pump noise | Low hydraulic fluid level | Turn sprayer OFF. Add fluid*. |
Electric motor does not operate | Power switch is not ON | Turn power switch to ON. |
| Tripped circuit breaker | Check circuit breaker at power source. |
|
| Reset motor switch. |
|
|
|
*Check hydraulic fluid level often. Do not allow it to become too low. Use only Graco approved hydraulic fluid.
8 | 311797F |
