Honeywell 2020 2020-5BE Product Specifications

11 - 3

2020-5BE Product Specifications

Parameter Specification

Dimensions (Typical):

Height 3.1 inches (7.9 cm)

Length 5.6 inches (14.2 cm)

Width 4.3 inches (10.9 cm)

Weight 8.8 ounces (250 g)

Voltage:

DC Barrel 8.5 to 9.5 volts

Host Port 4.7-12 volts

Current Draw: Base Only Base/Scanner w/ max charging

5 Volt Host 125 125mA (will not charge)

9 Volt DC Barrel 100 850mA

12 Volt Host 100 825mA

Charge Rate to Scanner Battery

41° F to +104° F (5° C to +40° C)

9 Volt DC Barrel (external

power)

Maximum 4 hours full charge for fully discharged

battery

Radio:

Frequency 2.4 to 2.4835 GHz (ISM Baqnd) Frequency Hopping

Bluetooth v.2.0 + EDR

Range 33 ft. (10m) typical

Data Rate 720 KBps - 3MBps

Temperature Ranges:

Operating 32° F to +122° F (0° C to +50° C)

Battery Charge 41° F to +104° F (5° C to +40° C)

Storage -40° F to +140° F (-40° C to +60° C)

Humidity Up to 95% non-condensing

Mechanical Drop Operational after 50 drops from 3.3 feet (1 m) to

concrete

Vibration Withstands 5G peak from 22 to 300 Hz

ESD Sensitivity 15 kV to any external surface

Contents

Main Disclaimer Bluetooth Product Agency Compliance USA FCC Part 15 Subpart C UL Statement Canada Industry Canada Europe Waste Electrical and Electronic Equipment Information ! Page Page Page Table of Contents Chapter 1 - Getting Started Chapter 2 - Terminal Interfaces Chapter 3 - Output Chapter 4 - Data Editing Chapter 5 - Data Formatting Chapter 6 - Symbologies Page Page Chapter 7 - Interface Keys Chapter 8 - Utilities Chapter 9 - Visual Xpress Chapter 10 - Serial Programming Commands Chapter 11 - Product Specifications Chapter 12 - Maintenance Chapter 13 - Customer Support Page Page 1 - 1 Getting Started About This Manual Unpacking the System Models 1 - 2 Cordless System: Main Components (See Product Specifications ! About the Battery .) 1 - 3 Battery Recommendations Proper Disposal of the Battery 1 - 4 Base Charge Mode Default = Automatic 1 - 5 Linking Image Scanner to Base Image Scanner Modes Unlinking the Image Scanner 1 - 6 Single Image Scanner Operation Default = Locked Link Mode Locked Link Mode - Single Image Scanner Open Link Mode - Single Image Scanner Override Locked Image Scanner Multiple Image Scanner Operation Image Scanner Name Changing Image Scanner Name - Serially 1 - 8 Changing Image Scanner Name - via Barcodes name 1 - 9 Image Scanner Report Application Work Groups Page 1 - 11 Current Application Work Group Resetting the Standard Product Default Settings: 1 - 12 Using the Image Scanner with Bluetooth Devices Changing Bluetooth PIN Code Out-of-Range Alarm Duration 1 - 13 Data Accumulation Mode 1 - 14 Batch Mode Transmit Delay Beeper and LED Sequences and Their Meaning Page 1 - 16 Note: Charging only occurs with external power applied to the 2020 or 12 volt Host power. Basic Operation of the Cordless System Cordless Base 1 - 17 RF (Radio Frequency) Module Operation Cordless Image Scanner System Conditions Linking Process Connecting the Base When Powered by Host (Keyboard Wedge) 1 - 19 1 - 20 Reading Techniques Standard Product Default Settings Resetting the Standard Product Defaults 1 - 21 Plug and Play Keyboard Wedge Connection Note: The following barcode also programs a carriage return (CR) suffix. Laptop Direct Connect RS-232 IBM 4683 Ports 5B, 9B, and 17 Interface Note: After scanning one of these codes, you must power cycle the cash register. 1 - 23 Connecting the Base with USB 1 - 24 IBM SurePos USB PC or Macintosh Keyboard Page 1 - 26 ACK/NAK Mode Connecting the Base with Serial Wedge Note: For the base to work properly, you must have the correct cable for your type of computer. 1 - 27 Page 2 - 1 Terminal Interfaces Terminal ID 2 - 2 Supported Terminals 2 - 3 Supported Terminals 2 - 4 Keyboard Country 2 - 5 Keyboard Country (continued) 2 - 6 Keyboard Style 2 - 7 Keyboard Modifiers 2 - 8 Connecting the Base with RS-232 Serial Port 2 - 9 RS-232 Baud Rate Default = 115,200 2 - 10 RS-232 Word Length: Data Bits, Stop Bits, and Parity RS-232 Handshaking 2 - 11 Default = RTS/CTS, XON/ XOFF and ACK/NAKOff. Host ACK Selection 2 - 12 Host ACK Enable 2 - 13 2020 Host Escape Commands 2 - 14 Wand Emu lation Code 39 Format only Wand Emulation Connection Same Code Format 2 - 15 Wand Emulation Transmission Rate Default = Idle High Default = 25 inches/second. Wand Emulation Polarity 2 - 16 Wand Emulation Data Block Size Default = 40 Wand Emulation Delay Between Blocks Default = 50ms. Output Image Scanner Functions Good Read Indicators Beeper Good Read Beeper Volume Good Read Default = Medium. Page 3 - 3 Good Read Delay Save Default = 0 ms (No Delay. User-Specified Good Read Delay Image Scanner Trigger Modes Page 3 - 5 Automatic Tri gger Presentation Mode 3 - 6 Hands Free Time-Out Reread Delay User-Specified Reread Delay 3 - 7 Centering Window 3 - 8 Preferred Symbology Note: A low priority symbol must be centered on the aiming pattern to be read. 3 - 9 High Priority Symbology Default = None Low Priority Symbology Default = None Output Sequence Overview 3 - 11 Output Sequence Editor Require Output Sequence 3 - 12 Output Sequence Example Note: Code 93 must be enabled to use this example. 3 - 13 Multiple Symbols Off On 3 - 14 No Read Video Reverse 4 - 1 Data Editing Prefix/Suffix Overview Points to Keep In Mind Default prefix = None. Default suffix = None To Add a Prefix or Suffix: 4 - 2 Example: Add a Suffix to a specific symbology To Clear One or All Prefixes or Suffixes: Page 4 - 4 Suffix Selections Function Code Transmit Default = Enable. Intercharacter, Interfunction, and Intermessage Delays 4 - 5 Intercharacter Delay Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay 4 - 6 Interfunction Delay Intermessage Delay 5 - 1 Data Formatting Note: The wildcard for all terminal types is 099. Data Format Editor Introduction Default Data Format setting = None. To Add a Data Format 5 - 2 Other Programming Selections Syntax = F4xxnn Syntax = F3ssxx Syntax = F2nnxx 5 - 3 Syntax = E9nn Syntax = E7xx Syntax = E6xx Syntax = F9xx 5 - 4 Syntax = E5. Syntax = ED Syntax = EC Syntax = FExx 5 - 5 Alternate Data Formats Page 6 - 1 Symbologies All Symbologies On Introduction All Symbologies 6 - 2 Message Length 6 - 3 Codabar Validate and Transmit <Default All Codabar Settings> Codabar Codabar Start/Stop Characters Default = Dont Transmit Codabar Check Character Default = No Check Character. No Check Character 6 - 4 Validate, but Dont Transmit with Codabar Concatenation Default = On. Code 39 < Default All Code 39 Settings > Code 39 Code 39 Start/Stop Characters Dont Tran smi t. 6 - 6 Code 39, continued Code 39 Check Character Default = No Check Character. Code 39 Message Length 6 - 7 Code 39, continued Code 39 Append Code 32 Pharmaceutical (PARAF) Note: Trioptic Code must be turned off to scan Code 32 Pharmaceutical codes. 6 - 8 Full ASCII Default = On 6 - 9 Code 39 Code Page Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 Check Digit Page 6 - 11 Code 93 < Default All Code 93 Settings > Code 93 Code 93 Message Length Code 93 Code Page Page 6 - 13 Straight 2 of 5 IATA, continued Straight 2 of 5 IATA Message Length Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Code 11 <Default All Code 11 Settings> Code 11 Page 6 - 16 Code 128, continued ISBT 128 Concatenation Default =Off. Code 128 Message Length Code 128 Code Page Tele pen <Default All Telepen Settings> Tele pen Telepen Output Default = AIM Telepen Output. UPC A <Default All UPC A Settings> UPC A Page 6 - 20 UPC A Addenda Separator UPC-A/EAN-13 with Extended Coupon Code UPC E <Default All UPC E Settings> 6 - 21 UPC E0 and UPC E1 Default = On (UPC E0) and Off (UPC E1). UPC E0 and UPC E1 Expand UPC E0 and UPC E1 Addenda Required Default = Not Required. Page EAN/JAN 13 <Default All EAN/JAN Settings> Page EAN/JAN 8 <Default All EAN/JAN 8 Settings> EAN/JAN 8 Page 6 - 27 MSI Validate, but Dont Transmit Validate and Transmit <Default All MSI Settings> MSI MSI Check Character Default = Validate Type 10, but Dont Transmit. MSI Message Length Page Page 6 - 30 GS1 DataBar Expanded GS1 DataBar Expanded Message Length GS1 Emulation Default = GS1 Emulation Off Page Page 6 - 33 PosiCode Message Length Trioptic Code Note: If you are going to scan Code 32 Pharmaceutical codes, Trioptic Code must be off. Page Page Page 7 - 1 Interface Keys Keyboard Function Relationships 7 - 2 7 - 3 7 - 4 7 - 5 7 - 6 Utilities Page 8 - 3 Resetting the Standard Product Default Settings: Temporary Visual Xpress Configuration Page 9 - 1 Visual Xpress Visual Xpress Introduction Visual Xpress Operations Scan Data Configure 9 - 2 Installing Visual Xpress from the Web 10 - 1 Serial Programming Commands option parameter Conventions Menu Command Syntax ^ ? * Concatenation of Multiple Commands 10 - 3 Responses Examples of Query Commands Example #1:What is the range of possible values for Codabar Coding Enable? Example #2: What is the default value for Codabar Coding Enable? Trigger Commands Current Application Work Group Standard Product Default Settings: Current Application Group 10 - 5 10 - 6 Menu Commands 10 - 7 Terminal Interfaces 10 - 8 10 - 9 10 - 10 10 - 11 Output Selections 10 - 12 10 - 13 Prefix/Suffix Selections 10 - 14 Data Formatter Selections Symbologies 10 - 15 10 - 16 10 - 17 10 - 18 10 - 19 10 - 20 10 - 21 10 - 22 Minimizing Bluetooth/ISM Band Network Activity 10 - 23 Page 11 - 1 Product Specifications 3820 Product Specifications 11 - 2 3820i Product Specifications 11 - 3 2020-5BE Product Specifications 11 - 4 2020-CBE Product Specifications 11 - 5 Keyboard Wedge 11 - 6 Wand Emul ati on 11 - 7 Serial Output 11 - 8 USB 12 - 1 Maintenance Maintenance Cleaning the Device ! 12 - 2 Replacing the 2020 Interface Cable: End Cap Changing the 3820/3820i Battery: Troubleshooting Base Note: Please visit the Services and Support section of our website ( ) to check for the latest software for both the image scanner and the base. Is the red LED on? 12 - 3 12 - 4 The image scanner wont read your barcode at all. 13 - 1 Customer Support Technical Assistance Online Technical Assistance 13 - 2 Product Service and Repair Online Product Service and Repair Assistance 13 - 3 Limited Warranty 13 - 4 A - 1 A Reference Charts Symbology Chart ASCII Conversion Chart (Code Page 1252 A - 2 ) Note: A - 3 A - 4 Code Page Mapping of Printed Barcodes Note: The Code Page option is available for Code 39, Code 93, and Code 128. B - 1 B Minimizing Bluetooth/ISM Band Network Activity Auto Reconnect Mode Default = Auto Reconnect On. B - 2 Maximum Link Attempts Default = 0. B - 3 Relink Time-Out Bluetooth/ISM Network Activity Examples Page Page Sample Symbols Programming Chart Note: