Honeywell NETAXS-123 4.0 System Configuration

48 www.honeywell.com

Installing the NetAXS-123 Panels

System Configuration

4.0 System Configuration

This section provides wiring diagrams for each of the NetAXS-123 system configurations.

4.1 Ethernet Connection

Figure 12: Ethernet Connection

Note: You should ground each NetAXS-123 Standard (Metal) Enclosure panel individually with an

Earth Ground.

NIC 100BaseT (CAT 5) 328 Ft. Max.

EG EGEG EG

DIP Switch Settings

S1-S5 Panel Address

S6: OFF

S7: OFF

S8-S9: ON: 485 Termination ON

DIP Switch Settings

S1-S5 Panel Address

S6: OFF

S7: OFF

S8-S9: ON: 485 Termination ON

NetAXS-123

Panel

Contents

Main Page C Installing the NetAXS-123 Panels Page LIST OF FIGURES Page LIST OF TABLES Page Installing the NetAXS-123 Panels In this chapter ... 1.0 Introduction 1.1 Access Control Overview 1.2 NetAXS-123 Overview 2.0 Panel Components and Descriptions Page 2.1 Supervised Input Wiring Page 2.2 NetAXS-123 Access Control Unit 2.2.1 NetAXS-123 Add-On Board 2.2.2 Supported Readers Supported readers include the following: Table 4: Readers Supported by NetAXS-123 2.2.3 Real-Time Clock Protection 2.3 Power Supply Page 3.0 Installation 3.1 Installing the Compact Enclosure Panel 3.1.1 Installing on a Wall Page Page Page Page 3.1.3 Installing on a Flat Surface 3.2 Installing the Standard Enclosure Panel Page Page Page Page Page Page Page Page 3.3 Installing the Add-On Board Page Page 3.4 Wiring the Readers Page Page Page 3.5 Wiring Door Strikes OR On-Board +12VDC Conguration External Power Supply Conguration Page Page ON ON OFF Future Use (Default) ON Future Use Table 8: NetAXS-123 SW1 DIP Switch Settings (continued) Page Page 3.6.2 Add-On Board DIP Switch and Jumper Settings Page 3.7 Communications 3.7.1 USB Communications Page 3.7.2 RS-485 Communications Page Page Page 4.0 System Configuration 4.1 Ethernet Connection 4.2 USB Connection 4.3 RS-485 Connection via PCI-3 Page 4.5 RS-485 Connections with Multidrop Panels at Both Ends of the Cable NetAXS-123 Access Control Unit Installation Guide, Document 800-05779, Revision A 53 Figure 17: RS-485 Connection via PCI-3 with Multidrop Panels at Both Ends Note: You should ground each NetAXS-123 Standard (Metal) Enclosure panel individually with an Earth Ground. PCI3 54 www.honeywell.com 4.6 M-56K Dial-up Modem, RS-485 Connection via Hub (PCI-3) Note: You should ground each NetAXS-123 Standard (Metal) Enclosure panel individually with an Earth Ground. DIP Switch Settings S1-S5 Panel Address S6: OFF S7: OFF S8-S9: OFF: 485 Termination OFF DIP Switch Settings S1-S5 Panel Address S6: OFF S7: OFF S8-S9: ON: 485 Termination ON Page Page Page 58 www.honeywell.com 4.10 NetAXS-123/NetAXS-123 Access Controller Panel Connection Detail X 485 - Figure 22: NetAXS-123/NetAXS-123 Access Controller Panel Connection Detail DO NOT CONNECT or GROUND SHIELD Ground only one side of cable shield Shield Page 5.0 Hardware Specifications 5.1 Relay Contacts 5.2 Reader Interface 5.3 Maximum Output Loading 5.4 PoE Power Limitations 5.5 Mechanical Page 6.0 Basic Standalone Operation 6.1 Card Read / Door Lock Operation 6.2 Door Egress / Door Lock / Door Status Operation 7.0 Maintenance 8.0 Troubleshooting Table11 Troubleshooting Problems and Solutions